[vadonchez]

Hi

Just to compare, here is a log from my cold start with "noise reduction ON" in MHD:




As you can see, my AFR falls into 10 area too then DME decrease STFT in order to keep AFR @14,7 target.

Only difference is that on my car both AFR reach 10 and both STFT are decreasing where in your log only bank2 is concerned.

I don't know why but it's like if the DME was in open loop at the beginning and then it goes into closed loop then lambda value is taken into account and STFT began to adjust fuel to reach AFR target....Then the LTFT takes over and STFT fall into 0 area....

[string_money]

Originally Posted by JustDriveIt

There seems to be more and more posts in the "General MHD" thread of people asking to have their logs read. I figured a separate thread for this would be a good idea.
I think it's awesome we have a community willing to help each other out and we certainly have some experts here that are good at looking at logs.

If someone is willing to add a post about the "general rule" when looking at logs (like what to look for - timing, boost, lpfp, etc.) I think that my also be helpful.

Hey all, been getting a high gear, high load misfire. Often results in "combustion misfire" in cylinder 3/4/5/6. Seems random between them all. Took a log today and leaned the f out it looks like. Can't tell if this is my HPFP, LPFP, Injectors, or what here. HPFP was replaced under warranty by previous owner. Can anyone take a look?

n54
85k miles
FBO
MHD stage 1
Index 7/8 injectors
New Sparkplugs

https://datazap.me/u/135igarrett/misfire?log=0&data=3-4-7-10-11-16-17&mark=50

[tej98]

Long time since I've done a log, but curious if anyone would like to take a look at an IKM0S tune I've been working on for my car:

https://datazap.me/u/tej98/1m-custom...og=0&data=3-23

I usually run MHD OTS maps but have been interested with the 1M throttle dampening settings (note, not the same as the 1m slider in MHD).

Thanks in advance!

[ESmotorsports]

Hey all. I have an N54 that got some bad gas that caused crazy timing corrections. I switched gas stations and recently performed a carbon cleaning. Since then, the car seems to be very happy, the timing corrections are all gone. Im hoping someone can take a look at my log and make sure all my numbers look good before I tune it up to MHD stage 2+. Any help would be appreciated.
https://datazap.me/u/es335/stage-0-0?log=0&data=3-23

[SlowE92]

Originally Posted by ESmotorsports

Hey all. I have an N54 that got some bad gas that caused crazy timing corrections. I switched gas stations and recently performed a carbon cleaning. Since then, the car seems to be very happy, the timing corrections are all gone. Im hoping someone can take a look at my log and make sure all my numbers look good before I tune it up to MHD stage 2+. Any help would be appreciated.
https://datazap.me/u/es335/stage-0-0?log=0&data=3-23

Are you not misfiring? Your short term trims are subtracting a LOT of fuel, and this is on the stock map. When was the last time you did a tune up?

[ESmotorsports]

No, it’s not misfiring at all. What would cause those trims to be so high?
What do you mean by tune up?

[eastsidaz]

Originally Posted by tej98

Long time since I've done a log, but curious if anyone would like to take a look at an IKM0S tune I've been working on for my car:

https://datazap.me/u/tej98/1m-custom...og=0&data=3-23

I usually run MHD OTS maps but have been interested with the 1M throttle dampening settings (note, not the same as the 1m slider in MHD).

Thanks in advance!

Generally you want the wgdc base slightly below your wgdc after PID. Your v3 looked much smoother. If your happy with that target boost than it looks fine.

Trims are a little far apart try to reset adaptions and see if they are better.

[sloN54]

hello internet, having an issue where the car is going into fuel mode 15 and leaning out hard

pure stage 2
walbro 450 + new regulator
e40 tune by CD919
index 11s
VRSF 4.5in intercooler
VRSF charge pipe w/ OEM diverter valves
ARM downpipe
XHP stage 3

i have replaced the fuel pump, HPFP, and regulator to try and get smooth fueling but it still seems all over the place

https://*********************/graphs...,22&zoom=-1,77