[NoGuru]

Originally Posted by rsyed07

Anybody here tried XHP's DCT flashes yet?

Yes but have not done much testing. Going to the drag strip tomorrow so I'll be able to gage it better after some runs.

[Luftfederman]

putting my 335is up for sale
2013
6 speed manual
about 90k miles
never tracked
summer only for last 4 years

anyone interested? it just went up on CarGuru

located in Pittsburgh

[luvmy_e92]

Originally Posted by rsyed07

Anybody here tried XHP's DCT flashes yet?

I flashed mine last week and it has been amazing so far. Stage 3 makes the gear changes even better and the new feature released to disable creep has been my favorite.

Here is a thread of some other people's experience:

https://bmw.***********.com/threads/...e-thread.6637/

[mawzi]

Anyone knows if the shift knob on the 6 spd 335is is attached to the boot?

My shift knob is showing signs of aging, and needs to be replaced, and someone is selling just the knob.

[JunkyardDogg]

Originally Posted by mawzi

Anyone knows if the shift knob on the 6 spd 335is is attached to the boot?

My shift knob is showing signs of aging, and needs to be replaced, and someone is selling just the knob.

it is attached

[mawzi]

Originally Posted by JunkyardDogg

it is attached

Can I still replace the handle only? Do I glue it back on or something?

[BSM n54iS]

Originally Posted by mawzi

Can I still replace the handle only? Do I glue it back on or something?

You should be able to tuck it under, but if needed maybe a little glue at the very top will help

[BSM n54iS]

Who here has upgraded their inlets with stockers? Is the effort worth it?

LMB335IS I know you did yours but are you on stock turbos still?

[BSM n54iS]

Originally Posted by masterstone

What's up IS bros/gals?

My original index 9 injectors are kicking the bucket and I have two problems at this point -
recall was for 07-08 335i only, index 8 and lower
extended limited warranty for 10 year / 120,000mi was for (basically) every car except ours.

Has anyone attempted to get these taken care of by BMW in either warranty or recall, and had any luck? The local dealer told me IF (big if) BMW were to retroactively reimburse me if I have them done, it would need to have been done by BMW.

Fun fact: In Canada they want $515 each for these suckers.

Ya I actually went to dealership to get walnut blasting and blower motor wire recall done, talked to my SA and told her I know for sure I needed new injectors. Had difficult startups and smelled of rich fuel from the exhaust. Mines a '11 btw and 10 year warranties are up in September for me fyi. But ya she completely hooked me up, had 1 injector fail and another was pretty bad but got 6 brand new index 12 because I had the old style index 8 I think and didn't charge me a diagnostic fee either. She also price matched a local shop for the walnut blasting so I gave her a nice tip.

Try the tip first if you need to

[LMB335IS]

Originally Posted by BdSM n54iS

Who here has upgraded their inlets with stockers? Is the effort worth it?

LMB335IS I know you did yours but are you on stock turbos still?

I did on stockers and it made a difference. My trap speeds went up. I'm on Pure 600's now

[BSM n54iS]

Originally Posted by LMB335IS

I did on stockers and it made a difference. My trap speeds went up. I'm on Pure 600's now

Nice, did you go 1.75" with stock then upgrade to 2" with the 600's or keep 2" the whole time? I'm only planning on getting the DD's when mine go out.

Was wondering too did you have a hard time with them fitting and staying on the small stock turbo inlet lip there? Thanks LMB

[LMB335IS]

Originally Posted by BdSM n54iS

Nice, did you go 1.75" with stock then upgrade to 2" with the 600's or keep 2" the whole time? I'm only planning on getting the DD's when mine go out.

Was wondering too did you have a hard time with them fitting and staying on the small stock turbo inlet lip there? Thanks LMB

2" the whole time. Inlets in general are PITA to install, at least the rear. I use hairspray. When it's wet it acts as a lubricant and dries sticky which helps to hold it in place on the lip while you crank down on the clamp. I had my son helping me and two pairs of hands definitely helps keeping everything aligned and square on the lip while getting it clamped down.

[BSM n54iS]

Originally Posted by LMB335IS

2" the whole time. Inlets in general are PITA to install, at least the rear. I use hairspray. When it's wet it acts as a lubricant and dries sticky which helps to hold it in place on the lip while you crank down on the clamp. I had my son helping me and two pairs of hands definitely helps keeping everything aligned and square on the lip while getting it clamped down.

Lol I haven't heard of using hairspray before, cool trick.

Ya it's the rear one that is making me hesitant of even doing it, and by myself I'm still leaning to get 1.75" and just get a new 2" set when I upgrade turbos, and probably get rid of my cobb catted dp's then also. Not sure yet what I want to do though.. I got a new CF intake being made in Japan right now so wanna match the connection point up nicely there when I put that on haha

[alpnwss]

There are companies that make adapters from 1.75 inlets to 2" turbos. I don't know if that 0.25 is a big deal. But it sounds better than getting new inlets.

[BSM n54iS]

Originally Posted by alpnwss

There are companies that make adapters from 1.75 inlets to 2" turbos. I don't know if that 0.25 is a big deal. But it sounds better than getting new inlets.

Are you talking about these?

https://www.precisionraceworks.com/1...RoCxV0QAvD_BwE

[IllSic_Design]

Originally Posted by BdSM n54iS

Are you talking about these?

https://www.precisionraceworks.com/1...RoCxV0QAvD_BwE

Those are backwards, For 2" inlets to go onto 1.75" stock turbos

[BSM n54iS]

Originally Posted by IllSic_Design

Those are backwards, For 2" inlets to go onto 1.75" stock turbos

Yes that's what I have, I think he was backwards haha

[IllSic_Design]

Originally Posted by BdSM n54iS

Yes that's what I have, I think he was backwards haha

oh whoops sorry, didn't read all the way through, just saw his and your comment.

[BSM n54iS]

Originally Posted by IllSic_Design

oh whoops sorry, didn't read all the way through, just saw his and your comment.

No worries, any word with those PR adapters? Haven't seen any reviews on them posted.

[IllSic_Design]

Originally Posted by BdSM n54iS

No worries, any word with those PR adapters? Haven't seen any reviews on them posted.

No, I haven't seen any. I didn't even know they made them, that's a pretty trick piece. They look like quality pieces, and most of PR's stuff is.

[BSM n54iS]

Originally Posted by IllSic_Design

No, I haven't seen any. I didn't even know they made them, that's a pretty trick piece. They look like quality pieces, and most of PR's stuff is.

Ya it looks like a nice piece, their coil kits are super popular. I'm trying to figure out though cuz I don't see those 3 dimples on the stock turbo that would hold it in place

Edit: Kinda decided to just go with 1.75" if I go the route since I'm not planning on going 600+ hp

[alpnwss]

Originally Posted by BdSM n54iS

Yes that's what I have, I think he was backwards haha

Turns out he is backwards haha. Wish I had known about these when I pulled the trigger on 1.75" thinking I'd stay stock forever. Maybe they'll make a flipped version?
This engine should come with a warning label like the drug commercials.