N54 Dyno Chart Compilation

s2k_335i · 12-10-2010, 11:28 PM

Quote:

Originally Posted by gbreeE90

Your numbers are very low for your mods, why did you remove IC?

The last time i ran this with the AMS FMIC, its was 370-380. I dont think the IC made up 60 hp. I sold my IC to my buddy.

Doug007 · 12-14-2010, 03:45 PM

If HP and TQ are on the same scale they will always cross at 5252 rpm.

If, however, the scaling is different they will cross somewhere else. The dyno on the top of page 2 has HP on a 0-350 scale and TQ on a 0-400 scale and the curves cross at about 4700 rpm. Plot them both 0-400 and you would be back to crossing at 5252rpm.

Quote:

Originally Posted by LaLakers91tc

they shouldn't ever cross at any other number....
HP is a number derived from Torque (foot pounds) x RPM / 5252

Thus at 5252 on every graph, torque will equal hp

R1000K3 · 12-14-2010, 04:15 PM

Quote:

Originally Posted by Quisp

I guess that makes sense to a degree, but the Dyno Dynamics one crosses under 4000 which wolld mean quite a large variance. Is there some other factor that would chnge the 5250 number?

The only factor that will make hp and tq values to cross at any other rpm than 5250 is when the torque is measured Metric units, i.e. Nm. The rpm crossing point will then be 5250*1.356 = 7120 rpm.

Quisp · 12-14-2010, 08:53 PM

Thanks for clearing it up.

m54b25 · 12-15-2010, 04:19 PM

Quote:

Originally Posted by bigdog34uz

These are some really high numbers for just a tune. Are all these on legit dyno's just curious. Mild Flash tune doing 344 with 364lbs of torque is high! I want those numbers. I want to do wife driving.

Yes, feel free to come to come to the dyno! The 1st dyno was done at the BMW Pembroke Meet... the new 15th run was retuned on 93octane Chevron 12-01-10. Just PAW Mild tune got better +10whp on stock car using barelly 14psi tapering to 8psi!

Users with the same tune on another E90 335i Steptronic w/10k RTF tires & full tank of gas has done 12.746@107.77Mph just with this tune.

timo1980 · 12-29-2010, 03:20 PM

07 335i coupe with procede and dual cone intake dyno graph(done at topspeed atlanta)

My2Cents · 12-29-2010, 09:41 PM

2007 335i e90 6MT. Dyno'd on Mustang Dyno.

Baseline:
Fully stock
4th gear pull
72 degrees F
91 octane

253.9 hp
247.7 Ft-Lbs.
--------
Mod'd results:
Dinan stage 2
Dinan exhaust
K&N drop in filter
4th gear pull
62 degrees F
91 octane

291.1 hp
310.9 Ft-Lbs.
--------
Gain of:
37.2 hp
63.2 Ft-Lbs.

My stock tq seems low. Most other stock numbers I have seen have been much higher than the hp number. Also my hp gains appear to be a bit low. What do you guys think?

BrianMN · 12-29-2010, 10:10 PM

All around it seems pretty low for stage 2, but it is still conservative and on a mustang.

jaybird124 · 12-29-2010, 11:35 PM

Sweet gains!

Penn999 · 01-10-2011, 12:12 AM

Stage 3 mods, 100 octane. (no meth) at 16psi. Mach V Dynojet(Blue) SAE. Bone stock 335i on 93 pump, same day, same dyno, also SAE. Why does almost everyone on here use STD....makes no sense. Use SAE. CORRECT THOSE NUMBERS....Since everyone else has STD here is a second graph with the same run only in STD. Gotta compare apples to apples.

RS LED · 01-10-2011, 12:14 AM

Injen intake
AR downpipe
HKS cat back
Vishnu V4
91 octane

I mess up with map, i switch around before dyno

but the numbers came out kinda low ...

any suggestion or commend?

run 1 map 1
run 2 map 2
run 2 map 2

ETS Michael · 01-11-2011, 04:00 AM

Stock Baseline
Procede Baseline (Autotune) V5 12-17 maps

Bone Stock.

Talk about a power change... It's amazing how the v5 transform the car without doing anything. This car is bone stock and makes amazing power and torque with no other mods. I will post up the rest of the runs with full bolt ons and step by step graphs shortly.

Michael

Penn999 · 01-11-2011, 10:58 AM

Quote:

Originally Posted by ETS Michael

Stock Baseline
Procede Baseline (Autotune) V5 12-17 maps

Talk about a power change... It's amazing how the v5 transform the car without doing anything. This car is bone stock and makes amazing power and torque with no other mods. I will post up the rest of the runs with full bolt ons and step by step graphs shortly.

Michael

I look forward to seeing those graphs of the step by step bolt on process. What psi was that full bolt on 92 pump number on. Also, I would like to see that graph. I havent updated to the V5 bc these new maps that are coming out soon...any eta on those. Robert said they should be out this week or next week right?

RS LED · 01-13-2011, 04:29 AM

What octane was it ?

Quote:

Originally Posted by ETS Michael

Stock Baseline
Procede Baseline (Autotune) V5 12-17 maps

Bone Stock.

Talk about a power change... It's amazing how the v5 transform the car without doing anything. This car is bone stock and makes amazing power and torque with no other mods. I will post up the rest of the runs with full bolt ons and step by step graphs shortly.

Michael

ETS Michael · 01-14-2011, 12:17 PM

92 pump gas from Chevron. We made 400 on pump with all the bolt ons.

Naptime · 01-18-2011, 03:14 AM

Quote:

Originally Posted by ETS Michael

92 pump gas from Chevron. We made 400 on pump with all the bolt ons.

Any pics of the exhaust?

ultimateracing335 · 01-26-2011, 10:33 PM

Ultimate Racing exhuast
Ultimate Racing downpipes
Ultimate Racing intake
Ultimate Racing bov
Jb4
Cooling mist dual cm7
Pump gas with 70 percent meth 30 percent water.
RB turbos

BrianMN · 01-26-2011, 11:43 PM

^ Holy cow that's a ton of power! You nearly held 500ft/lb of torque for a 4,000rpm range! And that's with stock turbos, on pump gas? I mean dang, that is extremely high.

Could we see some datalogs? Not questioning or anything, just like to see how it ran

ultimateracing335 · 01-27-2011, 01:25 AM

Quote:

Originally Posted by BrianMN

^ Holy cow that's a ton of power! You nearly held 500ft/lb of torque for a 4,000rpm range! And that's with stock turbos, on pump gas? I mean dang, that is extremely high.

Could we see some datalogs? Not questioning or anything, just like to see how it ran

Sorry Brian I forgot to add the RB turbos to to the list of mods. Data logs are on n54 tech and the tuning is a work in progress. Im having some fueling issues. NEED MORE FUEL!!!!

san6279 · 02-02-2011, 05:12 PM

Car:
e90 07 AT Sport Pkg

Mods:
Dinan Stage 2, CAI, Intercooler

Conditions:
Temp: 58 deg F
Hum: 12%

Dyno: Dynojet
Gear: 4th
Max HP: 299
Max Tq: 340
Max Boost: 14.35 psi

Numbers seem to be in line with what others are reporting, although max HP is quite a bit less than RWHP reported by Dinan @ 342. Dinan stock RWHP was 296. Also, their max flywheel Tq reported 421 at, deduct 15% for driveline (can you make that adj for Tq, same as hp?), call it 366. Dinan reports max boost at 13.2, so not sure if readings on this were accurate or not. These Dinan numbers w/o CAI or intercooler, which probably don't make a big diff anyway at the dyno. Generally happy with the car. A bit disappointed in the numbers.

acj75 · 02-03-2011, 12:51 PM

Quote:

Originally Posted by My2Cents

2007 335i e90 6MT. Dyno'd on Mustang Dyno.

Baseline:
Fully stock
4th gear pull
72 degrees F
91 octane

253.9 hp
247.7 Ft-Lbs.
--------
Mod'd results:
Dinan stage 2
Dinan exhaust
K&N drop in filter
4th gear pull
62 degrees F
91 octane

291.1 hp
310.9 Ft-Lbs.
--------
Gain of:
37.2 hp
63.2 Ft-Lbs.

My stock tq seems low. Most other stock numbers I have seen have been much higher than the hp number. Also my hp gains appear to be a bit low. What do you guys think?

Quote:

Originally Posted by san6279

Car:
e90 07 AT Sport Pkg

Mods:
Dinan Stage 2, CAI, Intercooler

Conditions:
Temp: 58 deg F
Hum: 12%

Dyno: Dynojet
Gear: 4th
Max HP: 299
Max Tq: 340
Max Boost: 14.35 psi

Numbers seem to be in line with what others are reporting, although max HP is quite a bit less than RWHP reported by Dinan @ 342. Dinan stock RWHP was 296. Also, their max flywheel Tq reported 421 at, deduct 15% for driveline (can you make that adj for Tq, same as hp?), call it 366. Dinan reports max boost at 13.2, so not sure if readings on this were accurate or not. These Dinan numbers w/o CAI or intercooler, which probably don't make a big diff anyway at the dyno. Generally happy with the car. A bit disappointed in the numbers.

Both of these seem a little low to me for a stage 2 Dinan tune. I just had my Dinan Stage 1 dyno'd a week ago on a Mustang at the local Cobb shop. I didn't get to do a stock baseline, but I added one at random from their database to this chart for comparison. Max boost on my car was 11.2 psi:

san6279 · 02-03-2011, 01:35 PM

Quote:

Originally Posted by acj75

Both of these seem a little low to me for a stage 2 Dinan tune. I just had my Dinan Stage 1 dyno'd a week ago on a Mustang at the local Cobb shop. I didn't get to do a stock baseline, but I added one at random from their database to this chart for comparison. Max boost on my car was 11.2 psi:

Thanks for the response. Wish I could load my graph. I only have a paper copy and no ability to scan right now.

One thing I'd like to add is info on air/fuel. It shows at about 15 from 2K to 3K and then tapers down to 12 by about 4.5K rpm. Is that normal?

I know, in general, there can be variations between dynos and even day to day, but just seems a bit low compared to some others I've seen online....and definitely from what Dinan reports.

Unfortunately I don't have a baseline to compare to.

Am considering sending the info to my SA to see if it is worth having Dinan take a look. I would expect a canned response, but no downside to asking.

12-14-2010, 08:53 PM	#48
Quisp Does not play well with others 81 Rep 1,787 Posts Drives: BMW Join Date: Apr 2007 Location: Arizona iTrader: (4)	Thanks for clearing it up. __________________
	Appreciate 0 Quote

12-29-2010, 03:20 PM	#50
timo1980 Private First Class 11 Rep 114 Posts Drives: 135i Join Date: Sep 2010 Location: santa clara, ca iTrader: (3)	07 335i coupe with procede and dual cone intake 07 335i coupe with procede and dual cone intake dyno graph(done at topspeed atlanta) Attached Images
	Appreciate 0 Quote

12-29-2010, 10:10 PM	#52
BrianMN Banned 116 Rep 2,428 Posts Drives: 4 Door Family Sedan Join Date: Sep 2009 Location: Minneapolis iTrader: (7)	All around it seems pretty low for stage 2, but it is still conservative and on a mustang.
	Appreciate 0 Quote

12-29-2010, 11:35 PM	#53
jaybird124 Major 161 Rep 1,046 Posts Drives: 2017 M3 ZCP Join Date: Nov 2005 Location: Florida iTrader: (0)	Sweet gains! __________________ '17 M3 Imola Red/Carbonstructure Cloth, Competition, Lighting, 6MT Retired: '93 325i \|'99 Jeep Wrangler Sport \|'06 330i Sport \|'08 335i Sport \|'08 328i Sport \|'09 335d Sport
	Appreciate 0 Quote

01-10-2011, 12:12 AM	#54
Penn999 Lieutenant Colonel 52 Rep 1,661 Posts Drives: 335i coupe Join Date: May 2010 Location: VA iTrader: (3)	Stage 3 mods, 100 octane. (no meth) at 16psi. Mach V Dynojet(Blue) SAE. Bone stock 335i on 93 pump, same day, same dyno, also SAE. Why does almost everyone on here use STD....makes no sense. Use SAE. CORRECT THOSE NUMBERS....Since everyone else has STD here is a second graph with the same run only in STD. Gotta compare apples to apples. Attached Images __________________ 07' MT, Quaife LSD, BMW Performance LED Steering Wheel, HPF FMIC, AA BOV, HPF Exhaust, DCI, Procede V5, AR Stage 1 oil cooler, AR OCC, AR CL DP's, Vishnu Meth Kit, UUC SSK+DSSR, UUC Shift knob, (19 inch)VMR V715's/Yokohama Advan AD08's, Hartge Pedals and Floor Mats. Awaiting Install: M3 Rear Subframe Bushings, Full M3 suspension bits, AST 4100's, DSS axles. Future plans: Vishnu Single turbo kit Last edited by Penn999; 01-10-2011 at 12:34 AM..
	Appreciate 0 Quote

01-10-2011, 12:14 AM	#55
RS LED 14 Rep 318 Posts Drives: E92 Join Date: Jan 2009 Location: SoCal iTrader: (5)	Injen intake AR downpipe HKS cat back Vishnu V4 91 octane I mess up with map, i switch around before dyno but the numbers came out kinda low ... any suggestion or commend? run 1 map 1 run 2 map 2 run 2 map 2
	Appreciate 0 Quote

01-11-2011, 04:00 AM	#56
ETS Michael Major 77 Rep 1,155 Posts Drives: 335i Join Date: May 2009 Location: Vancouver, WA iTrader: (4)	Stock Baseline Procede Baseline (Autotune) V5 12-17 maps Bone Stock. Talk about a power change... It's amazing how the v5 transform the car without doing anything. This car is bone stock and makes amazing power and torque with no other mods. I will post up the rest of the runs with full bolt ons and step by step graphs shortly. Michael Last edited by ETS Michael; 01-11-2011 at 04:10 AM..
	Appreciate 0 Quote

01-14-2011, 12:17 PM	#59
ETS Michael Major 77 Rep 1,155 Posts Drives: 335i Join Date: May 2009 Location: Vancouver, WA iTrader: (4)	92 pump gas from Chevron. We made 400 on pump with all the bolt ons.
	Appreciate 0 Quote

01-26-2011, 10:33 PM	#61
ultimateracing335 Second Lieutenant 37 Rep 220 Posts Drives: blk 335i sedan with mods Join Date: Oct 2008 Location: toronto canada iTrader: (0)	Ultimate Racing exhuast Ultimate Racing downpipes Ultimate Racing intake Ultimate Racing bov Jb4 Cooling mist dual cm7 Pump gas with 70 percent meth 30 percent water. RB turbos Attached Images Last edited by ultimateracing335; 01-27-2011 at 01:22 AM..
	Appreciate 0 Quote

01-26-2011, 11:43 PM	#62
BrianMN Banned 116 Rep 2,428 Posts Drives: 4 Door Family Sedan Join Date: Sep 2009 Location: Minneapolis iTrader: (7)	^ Holy cow that's a ton of power! You nearly held 500ft/lb of torque for a 4,000rpm range! And that's with stock turbos, on pump gas? I mean dang, that is extremely high. Could we see some datalogs? Not questioning or anything, just like to see how it ran
	Appreciate 0 Quote

02-02-2011, 05:12 PM	#64
san6279 First Lieutenant 9 Rep 338 Posts Drives: 2007 335i Join Date: Sep 2010 Location: Seattle, WA iTrader: (2)	Car: e90 07 AT Sport Pkg Mods: Dinan Stage 2, CAI, Intercooler Conditions: Temp: 58 deg F Hum: 12% Dyno: Dynojet Gear: 4th Max HP: 299 Max Tq: 340 Max Boost: 14.35 psi Numbers seem to be in line with what others are reporting, although max HP is quite a bit less than RWHP reported by Dinan @ 342. Dinan stock RWHP was 296. Also, their max flywheel Tq reported 421 at, deduct 15% for driveline (can you make that adj for Tq, same as hp?), call it 366. Dinan reports max boost at 13.2, so not sure if readings on this were accurate or not. These Dinan numbers w/o CAI or intercooler, which probably don't make a big diff anyway at the dyno. Generally happy with the car. A bit disappointed in the numbers.
	Appreciate 0 Quote