[Mircea]

Originally Posted by Phil325i

I doubt NOx sensor would cause a misfire. I still think you're right - it's injector(s). See this thread:

https://www.e90post.com/forums/showt...5#post23587995

If you can afford it, I'd replace all six injectors, not just one bank.

Yeah that's definitely what I'm going to do, will get them for £1110 from Cooper Tunbridge Wells as I couldn't find any cheaper that have warranty.
Will install them myself and will have a full service done on it with oil and all filters changed.

Ultimately, if the problem is still there, I'll go like that thread suggests, to MapTech to get it remapped and NOx coded out. I've emailed them to get a quote and the whole shebang is actually cheaper than a NOXEM unit and + it's a stage 1 remap which gives the car some extra power too which seems like a win-win.

[Mircea]

Originally Posted by Phil325i

I doubt NOx sensor would cause a misfire. I still think you're right - it's injector(s). See this thread:

https://www.e90post.com/forums/showt...5#post23587995

If you can afford it, I'd replace all six injectors, not just one bank.

Update: I have continued querying about the procedure with MapTech and they told me if I have NOx cat issues, just coding out the NOx sensor wouldn't fix those. I'd additionally have to have the secondary cat removed.
They told me it would obviously cost extra, but that I could have it done at any other garage if I wanted to.

However, what's just curious is that in the thread there, Will_460cs says it fixed the NOx ageing issues for him and hasn't mentioned anything about removing the cats themselves. He hasn't been online since last year though, so I think waiting for a reply to the PM I sent him is hopeless...

[mahoone]

Replacing NOX sensor or coding it out won't fix the leaking injectors so I would get them done first.

I've got NOXEM installed for a year now and it does its job. No more NOX error codes and the car operates in Strafited mode as it should.
There's no need to remove cats because there's probably nothing wrong with them. It's the error code (30E9) that's preventing your engine to operate in Stratify mode.

What error codes are you getting now? Is it just 2DED and 30E9?
Any misfire codes?

[Mircea]

Originally Posted by mahoone

Replacing NOX sensor or coding it out won't fix the leaking injectors so I would get them done first.

I've got NOXEM installed for a year now and it does its job. No more NOX error codes and the car operates in Strafited mode as it should.
There's no need to remove cats because there's probably nothing wrong with them. It's the error code (30E9) that's preventing your engine to operate in Stratify mode.

What error codes are you getting now? Is it just 2DED and 30E9?
Any misfire codes?

I've said earlier that I'll replace all 6 injectors first.
Then I'll clear out errors, reset adaptations and drive for about 200-300km. Only after, if the cat errors return or I'm not satisfied with how it runs I'll take it to the remap guys. I'll order the injectors next week and fingers crossed I fix the issue.

You can look in the full history of the errors in that folder and see it says something about cylinders 4 and 6 (29CE and 29D0). I've looked at the km timestamp of these and they coincide exactly with when I remember getting the CEL. Last occurrence was precisely on my way to the garage, and again a start-stop of the engine cured this.
I have also had a read about that 2FDA error that popped up once ever, about 1.5k miles away just to ease my mind. Section 1 of https://bimmerprofs.com/hpfp/ which includes my code, mentions one of the most probable cause of this being leaky injectors.

I think the 2DED code you can ignore as that literally came and went, and is most probably caused by my cable/obd port/laptop's connection.

I'm just curious if the OP in that thread had to get his secondary cat removed to get rid of the 30E9 cat aging error (like the remap guys told me they need to) or if just the coding out of the NOx sensor did it (like he said it did)...

[Mircea]

Update:

I have just tested my PCV for whistles while the engine is running and there are no sounds, just a very very tiny whistle when I partly put my finger over the breather. Also opened the oil filler cup with the engine running, there is almost no vacuum though there is definitely some air getting sucked in with it open, and the idle just went nuts until I put it back on, all of which I have read is normal.

I have also cleaned my intake VANOS solenoid (looked like this https://i.ibb.co/jvGYmzq/IMG-0509.jpg) it made no difference from what I could tell, though the engine was already warm when I started up the car, but there were still slight shakes and smell of petrol quickly after startup. I'll see in the morning but I have little hope for this. Was worth a try though.

Anything else I could try doing before ordering the injectors or while waiting for them?

[Mircea]

Update:

Bought the new index 11s, replaced and coded them yesterday, reset errors and adaptations and redid them.
Here's how the old ones looked with emphasis on the ones that looked worst.
There was some oil on some of them from halfway down but I guess that's from when I had the leaky VCG. One of them especially had oil with this white vanilla-like colour to it which I guess is just dust? Neither smelled of anything unusual.

Will have the oil changed and filters replaced this week hopefully.

I started the car up this morning after a ~10h sit and the problem seems to be gone where there were shakes and idle fluctuations at cold there's no more. Only time will tell though, this week'll be a trial.

I still have the 30E9 error code popping up though, but this will probably be for another thread later on.

Cheers everyone for the help!

[mahoone]

That's great! Well done
I had the 30E9 code when I bought the car. I ended up buying NOXEM which got rid of it permanently.
When you start the car in the morning does it rev up to 700-800 rpm and then gradually drop down to idle rpm?

Here's what mine look like:

[Mircea]

Originally Posted by mahoone

I had the 30E9 code when I bought the car. I ended up buying NOXEM which got rid of it permanently.

I am considering this or the decat/remap way as outlined here, since both options cost roughly the same. Just need to clear some things out about their process first.

Originally Posted by mahoone

That's great! Well done
When you start the car in the morning does it rev up to 700-800 rpm and then gradually drop down to idle rpm?

Yeah that's exactly what it did this morning, though it was -1*c and it stayed 1-2min in the higher revs until calming down to ~600rpm.
No shakes or petrol smell!

[OliSharp]

Is there a particular online guide you followed to code your injectors and re-set adaptations. I know there are loads but I'm looking for a good one!

Originally Posted by Mircea

Update:

Bought the new index 11s, replaced and coded them yesterday, reset errors and adaptations and redid them.
Here's how the old ones looked with emphasis on the ones that looked worst.
There was some oil on some of them from halfway down but I guess that's from when I had the leaky VCG. One of them especially had oil with this white vanilla-like colour to it which I guess is just dust? Neither smelled of anything unusual.

Will have the oil changed and filters replaced this week hopefully.

I started the car up this morning after a ~10h sit and the problem seems to be gone where there were shakes and idle fluctuations at cold there's no more. Only time will tell though, this week'll be a trial.

I still have the 30E9 error code popping up though, but this will probably be for another thread later on.

Cheers everyone for the help!

[threethirtyi]

My E93 330i 2007/8 sometimes doesn’t crank but I can hear the starter motor spinning without cranking the engine.

And when it does crank the engine the revs keep going up and down then eventually engine stops running suddenly. Some misfires when I rev up.

I can sometimes keep the revs up but when I sudden rev it misfires and doesn’t rev up as fast as it should.

Ran some codes it comes up with high pressure fuel pump.

Would replacing the HPFP do the job? Or sounds like another issue also?