[lnxguy]

It's really not that difficult. It's actually pretty simple.. Even the parts people have trouble with (the rubber accordian flex pipe in the trunk) took me maybe 10 seconds to fish the wire through? A little common sense goes a long way.

[BIMMER_Tech 631]

Originally Posted by Rotary Rasp

You do realize that this is my thread, right?

So using this harness, you dont need to do any splicing, just transfer wires from OEM Quadlock connector to harness?

http://www.ebay.com/itm/1-1-Most-Qua...dYGe4~&vxp=mtr

[tiburcin]

Do you know if it works in a CIC business navigator? I mean, the small screen CIC? I've done everything as the firs post but it doesn't work.

[btelega]

tiburcin, good question.
I also have CIC-MID (S606) and i am curious if the rear camera will work.

[jrdnlc]

Will this work on a CIC retrofit? I have PDC.

[Rotary Rasp]

Originally Posted by BIMMER_Tech 631

So using this harness, you dont need to do any splicing, just transfer wires from OEM Quadlock connector to harness?

http://www.ebay.com/itm/1-1-Most-Qua...dYGe4~&vxp=mtr

You still need to cut and splice, but you'll be able to do it outside the car on a workbench.

[btelega]

Will rear camera works with CIC businnes (small screen) ??

[Torqu3]

I have a bit of a silly question, that I'm sure you can help me out with. The little rubber piece on the handle has worn holes through it, so I figured instead of replacing it with the same old part, I'd get a fancy new backup camera. My car has comfort access so when I pull the trunk handle, it opens up, even when the car is locked. These handles that are posted all through this thread keep that same functionality, right?


Also, I have PDC. That doesn't change the process any, does it?


I'd like to fit a front camera at some point too, but that isn't a very pressing issue.

[NYBulldog]

My retrofit for this kit never worked, I suspected the emulator was no good. Never initialized. At least my OEM PDC retrofit beeps inside.

[OneSickM]

Originally Posted by Rotary Rasp

You still need to cut and splice, but you'll be able to do it outside the car on a workbench.

I went through all the pages but I am still not sure how do you ground the camera to the chassis? How do you ground it? Where do you attach the black spliced wire exactly?

[lnxguy]

Originally Posted by s65M3_e92

I went through all the pages but I am still not sure how do you ground the camera to the chassis? How do you ground it? Where do you attach the black spliced wire exactly?

There's a grounding block behind the passenger rear side bolster. That's where I attached mine. The entire seat side bolster just pulls off, super easy.

[OneSickM]

Originally Posted by lnxguy

There's a grounding block behind the passenger rear side bolster. That's where I attached mine. The entire seat side bolster just pulls off, super easy.

Great thanks! Are there any clips that I have to be aware of to not be broken?

[lnxguy]

Originally Posted by s65M3_e92

Great thanks! Are there any clips that I have to be aware of to not be broken?

Nope shouldn't be. Once the seat back is released the side bolster just pops off.

[OneSickM]

Originally Posted by Rotary Rasp

You still need to cut and splice, but you'll be able to do it outside the car on a workbench.

Originally Posted by lnxguy

There's a grounding block behind the passenger rear side bolster. That's where I attached mine. The entire seat side bolster just pulls off, super easy.

I cannot find this line in CIC ecu. Is it located in different ECU?

PDC_DIRECTION
vertikal

Anyone can help?

[lnxguy]

Nope, it's in the CIC ECU.

[OneSickM]

Originally Posted by lnxguy

Nope, it's in the CIC ECU.

looking for more input as when I put into reverse, nothing happens

Any reason why I don't see it in my .TRC?
Do I need to default all models after adding VO or just adding VO to CAS and NFRM is enought?

[lnxguy]

No need to reset anything after writing $3AG to the CAS and FRM. Are you sure you're reading the correct module in NCS Expert? What version is your CIC? 13? 16? C1A?

[OneSickM]

Originally Posted by benj04

Hello
I did everything as it should But still does not work I think the version of the CiC is the CIC C.08 problem . Is this possible?
This ligne:
PDC_DIRECTION
vertikal
is not in the cic module. I have the rear pdc
If I activate this line:
MACRO_L6_PARKMENU
aktiv
the image of the PDC do not appear

I do not understand anything

Originally Posted by lnxguy

No need to reset anything after writing $3AG to the CAS and FRM. Are you sure you're reading the correct module in NCS Expert? What version is your CIC? 13? 16? C1A?

I have the same exact problem as the post above. My CIC version is same as well as above CIC C.08

Do you think I need to update the firmware? if yes, is there easy way?

[Alex_WLY]

I have c09 and it dosen' t work...so you need to update CIC.

[OneSickM]

Originally Posted by Alex_WLY

I have c09 and it dosen' t work...so you need to update CIC.

Ohh boy.. and I bought the camera and emulator thinking that I could do this rerofit easily. Do you know how can I update it?

[lnxguy]

You can use WinKFP to update your CIC module.

[vespa]

You can't (reasonably) update your CIC. You either have to pay the dealer a few hundred dollars or spend a lot more money trying to do it yourself.

The good news is that you don't need to update it. You don't have CIC.08, that's just the default version that it shows before reading the module. Do a "lessen" so it can read your actual version.