**First Time Tuners** Start Here** Official Misfire Thread| Updated!

achien · 04-07-2012, 08:13 PM

your next step is to clean out the carbon build up.

Quote:

Originally Posted by saxon

Cyl 5 misfire only in high rpm/high load, replaced all plugs and a new coil for cyl 5 and got the code again, car runs really rough after a pull and after a couple of mins startsrunning properly again

07 with 43k miles

Ant Anthem · 04-13-2012, 08:31 AM

Quote:

Originally Posted by Yeahdickey

Well ... I am officially depressed. Brought it to the dealer today and they are telling me that at least two of the injectors were replaced or checked, back in May at another BMW dealer, and they botched the install, as these injectors have a broken tab and perhaps O ring???

Either way they do not want to touch it and are telling me that i should go back to the other dealer. Their concerns are that they will not get paid for the work they do, because when they send the parts back to BMW NA, they will see they were installed incorrectly, and deny to pay the claim.

I have been on the phones all day with both dealers and with BMW NA. I am getting no where and to be honest with you, I do not want to go back to the original dealer (Braman BMW Miami) regardless, because they clearly messed it up the first time and I am hearing horror stories on their incompetence .

I went back to the dealer this afternoon and pleaded with their Service Director to work with me. They are looking at it deeper now and I honestly think they best i can hope for from them, is a discount on parts and labor. They will "work with me".

I feel defeated. Again, BMW NA, did not want to work with me at all.

I'm buying a '07 335 that was originally serviced by Braman BMW. Injectors were changed in 2010 and car has 20k miles since then. Should I be concerned?

manny127 · 04-22-2012, 01:54 AM

I've got a misfire on cylinder 5 after installing JB4 running Map 1. I was doing a WOT pull when all of a sudden the car started shaking and I got a CEL. I immeadately changed to map 0 with no difference car kept shivering when i touched the gas. When I restarted everything was fine. The question I have is if I put the car in Map 0 now and pull out the JB4 and take it to the dealer will they see only the misfire code or would there be any other codes that indicate a tune? I want them to investigate the misfire, I havent gotten my plugs changed yet under the service plan! (Only 23000 miles (37000kms) on the car)

BADS335 · 04-24-2012, 09:16 AM

I started a thread, but not getting much for responses. I have a missfire in one cylinder. Replaced plugs, coil and injector. Same code. If it was carbon, wouldn't it be accross all cylinders not just one? I am lost and need some guidance.

Thanks

Jeff@TopGearSolutions · 04-24-2012, 09:52 AM

Quote:

Originally Posted by BADS335

I started a thread, but not getting much for responses. I have a missfire in one cylinder. Replaced plugs, coil and injector. Same code. If it was carbon, wouldn't it be accross all cylinders not just one? I am lost and need some guidance.

Thanks

When does the misfire occur? At idle or wide open throttle at what RPM?

enrita · 04-24-2012, 10:16 AM

Quote:

Originally Posted by BADS335

I started a thread, but not getting much for responses. I have a missfire in one cylinder. Replaced plugs, coil and injector. Same code. If it was carbon, wouldn't it be accross all cylinders not just one? I am lost and need some guidance.

Thanks

does it occur on pump gas or with meth?
Did you try changing maps ?

BADS335 · 04-24-2012, 10:23 AM

Quote:

Originally Posted by Jeff@topgearsolutions

When does the misfire occur? At idle or wide open throttle at what RPM?

I am running pump gas 93 oct. No meth. Happens most prodominantly at idle and light load mainly. But feels down on power all around.

enrita · 04-24-2012, 10:36 AM

Quote:

Originally Posted by BADS335

I am running pump gas 93 oct. No meth. Happens most prodominantly at idle and light load mainly. But feels down on power all around.

did you try removing the tune ?

Jeff@TopGearSolutions · 04-24-2012, 10:38 AM

Quote:

Originally Posted by BADS335

I am running pump gas 93 oct. No meth. Happens most prodominantly at idle and light load mainly. But feels down on power all around.

If it was at or near idle I would think it might be something more fuel related like hpfp or lpfp. Sometimes you would have other codes.

How did the plugs look when you removed them?

I'm assuming your injectors were coded properly?

BADS335 · 04-24-2012, 10:39 AM

Quote:

Originally Posted by enrita

did you try removing the tune ?

Yes. Happens with and without tune.

BADS335 · 04-24-2012, 10:51 AM

Quote:

Originally Posted by Jeff@topgearsolutions

If it was at or near idle I would think it might be something more fuel related like hpfp or lpfp. Sometimes you would have other codes.

How did the plugs look when you removed them?

I'm assuming your injectors were coded properly?

Plugs looked great. I just put them in about 2k miles ago. But pulled them to check. Color is good, condition is good.

I am not sure it is the fp. If it was multiple cylinders and codes, but I am getting one code for one cylinder. Well I am getting two codes. 10703 and 11170. But I get 11170 all the time and for no clear reason and no one seems to know what it means. I am getting ready to leave the car on the side of the road.

Jeff@TopGearSolutions · 04-24-2012, 10:53 AM

Quote:

Originally Posted by BADS335

Plugs looked great. I just put them in about 2k miles ago. But pulled them to check. Color is good, condition is good.

I am not sure it is the fp. If it was multiple cylinders and codes, but I am getting one code for one cylinder. Well I am getting two codes. 10703 and 11170. But I get 11170 all the time and for no clear reason and no one seems to know what it means. I am getting ready to leave the car on the side of the road.

That does sound annoying.

Have you tried resetting adaptations? I never heard of 11170 code either.

BADS335 · 04-24-2012, 11:01 AM

I have not tried that yet. Worth a shot. I may pull the intake manfold and look at what kind of carbon build up I have...but I find it hard to believe it is only one cylinder that would be impacted.

TheSoCal335i · 05-21-2012, 01:11 AM

what are the best injectors to get for my 07 335? i just checked the computer today and it says theres 31000 miles on them i should change them right?

NoQuarter · 05-23-2012, 10:59 AM

Took my 535 in today for misfire on cylinder 3 that I could not resolve with a new coil or plug. Got word the injector is definitely bad but they are also looking into replacing the cylider head.

BlueBimmer · 05-23-2012, 04:10 PM

Quote:

Originally Posted by manny127

I've got a misfire on cylinder 5 after installing JB4 running Map 1. I was doing a WOT pull when all of a sudden the car started shaking and I got a CEL. I immeadately changed to map 0 with no difference car kept shivering when i touched the gas. When I restarted everything was fine. The question I have is if I put the car in Map 0 now and pull out the JB4 and take it to the dealer will they see only the misfire code or would there be any other codes that indicate a tune? I want them to investigate the misfire, I havent gotten my plugs changed yet under the service plan! (Only 23000 miles (37000kms) on the car)

Did you get this resolved? I don't see any responses and I'm curious to know what happened?
Thanks.

ZTZ1010 · 05-27-2012, 03:23 PM

Had the car in last week for a misfire on cyl 3. they replaced all 6 spark plugs and put a new injector put in cyl 3. driving today and low and behold, misfire cyl 3. swapped coilpacks to see if the misfire would follow, still cyl 3.

any clue what else it could be? I'd be shocked if it was carbon buildup, as I only have 35k on my 335 and have been running meth for almost 15k of that.. the only code being thrown is 29CF. no HPFP/LPFP related codes so I'm not sure where to go from here... I'll bring the car in next week but any advice would be helpful in the meantime!

thanks

e90328i · 06-20-2012, 10:41 AM

heys guys, getting somewhat consistent misfire/limp mode while wot 3rd-4th gear 3k rpms
plugs were changed 6k miles ago along with injectors and hpfp. I have 63k miles without a carbon cleaning, would that be the culprit? anyways i will post some codes when im back in town tomorrow.

Spun Crankhub · 06-30-2012, 06:06 PM

Misfire on Cyliner 5 ONLY with tune in the car, no code when tune is out. I have JB3(pulling it again today to do JB4 upgrade.) I am confused why the misfire only on hard pulls, with software, but I can go hard with no tune and not throw a code. What gives?!?

Exzackt · 07-26-2012, 12:25 PM

Quote:

Originally Posted by ZTZ1010

Had the car in last week for a misfire on cyl 3. they replaced all 6 spark plugs and put a new injector put in cyl 3. driving today and low and behold, misfire cyl 3. swapped coilpacks to see if the misfire would follow, still cyl 3.

any clue what else it could be? I'd be shocked if it was carbon buildup, as I only have 35k on my 335 and have been running meth for almost 15k of that.. the only code being thrown is 29CF. no HPFP/LPFP related codes so I'm not sure where to go from here... I'll bring the car in next week but any advice would be helpful in the meantime!

thanks

hey did you ever fix your misfire issues.. my car is having very similar problems

Exzackt · 07-26-2012, 12:26 PM

Quote:

Originally Posted by MontegoChris

Misfire on Cyliner 5 ONLY with tune in the car, no code when tune is out. I have JB3(pulling it again today to do JB4 upgrade.) I am confused why the misfire only on hard pulls, with software, but I can go hard with no tune and not throw a code. What gives?!?

same problem here.. had injectors and fuel pump replaced and nothing

Jeff@TopGearSolutions · 07-26-2012, 01:22 PM

Quote:

Originally Posted by MontegoChris

Misfire on Cyliner 5 ONLY with tune in the car, no code when tune is out. I have JB3(pulling it again today to do JB4 upgrade.) I am confused why the misfire only on hard pulls, with software, but I can go hard with no tune and not throw a code. What gives?!?

Quote:

Originally Posted by Exzackt

same problem here.. had injectors and fuel pump replaced and nothing

Sparkplugs replaced every 25K miles?

04-22-2012, 01:54 AM	#91
manny127 Private 5 Rep 61 Posts Drives: 09 335i Coupe (E92) Join Date: Jul 2009 Location: Mississauga iTrader: (3)	I've got a misfire on cylinder 5 after installing JB4 running Map 1. I was doing a WOT pull when all of a sudden the car started shaking and I got a CEL. I immeadately changed to map 0 with no difference car kept shivering when i touched the gas. When I restarted everything was fine. The question I have is if I put the car in Map 0 now and pull out the JB4 and take it to the dealer will they see only the misfire code or would there be any other codes that indicate a tune? I want them to investigate the misfire, I havent gotten my plugs changed yet under the service plan! (Only 23000 miles (37000kms) on the car)
	Appreciate 0 Quote

04-24-2012, 09:16 AM	#92
BADS335 Lieutenant 35 Rep 408 Posts Drives: Montego 335i E90 Join Date: Sep 2010 Location: Chicago iTrader: (2)	I started a thread, but not getting much for responses. I have a missfire in one cylinder. Replaced plugs, coil and injector. Same code. If it was carbon, wouldn't it be accross all cylinders not just one? I am lost and need some guidance. Thanks
	Appreciate 0 Quote

04-24-2012, 11:01 AM	#101
BADS335 Lieutenant 35 Rep 408 Posts Drives: Montego 335i E90 Join Date: Sep 2010 Location: Chicago iTrader: (2)	I have not tried that yet. Worth a shot. I may pull the intake manfold and look at what kind of carbon build up I have...but I find it hard to believe it is only one cylinder that would be impacted.
	Appreciate 0 Quote

05-21-2012, 01:11 AM	#102
TheSoCal335i Private 5 Rep 69 Posts Drives: 07 335i Join Date: Apr 2012 Location: SoCal iTrader: (0)	what are the best injectors to get for my 07 335? i just checked the computer today and it says theres 31000 miles on them i should change them right?
	Appreciate 0 Quote

05-23-2012, 10:59 AM	#103
NoQuarter Captain 168 Rep 906 Posts Drives: 2008 535xi / 2011 Z4 35Is Join Date: Jan 2011 Location: Indiana iTrader: (0) Garage List 2018 BMW X2 [0.00] 2008 535xi [0.00] 2011 Z4 35is [0.00]	Took my 535 in today for misfire on cylinder 3 that I could not resolve with a new coil or plug. Got word the injector is definitely bad but they are also looking into replacing the cylider head.
	Appreciate 0 Quote

05-27-2012, 03:23 PM	#105
ZTZ1010 Aficionado of All Things Vroom 184 Rep 1,217 Posts Drives: 2020 F97 X3M Competition Join Date: Feb 2008 Location: Connecticut iTrader: (9)	Had the car in last week for a misfire on cyl 3. they replaced all 6 spark plugs and put a new injector put in cyl 3. driving today and low and behold, misfire cyl 3. swapped coilpacks to see if the misfire would follow, still cyl 3. any clue what else it could be? I'd be shocked if it was carbon buildup, as I only have 35k on my 335 and have been running meth for almost 15k of that.. the only code being thrown is 29CF. no HPFP/LPFP related codes so I'm not sure where to go from here... I'll bring the car in next week but any advice would be helpful in the meantime! thanks __________________ Current: 2020 F97 X3M Competition Retired: '18 6MT AW F30 340x Drive \| '15 6MT F80 M3\| '11 AW DCT E92 M3\| '09 6MT AW E90 335i\| 08' 6MT E92 328xi
	Appreciate 0 Quote

06-20-2012, 10:41 AM	#106
e90328i Banned 25 Rep 386 Posts Drives: 07 E90 335i Join Date: May 2011 Location: socal iTrader: (4)	heys guys, getting somewhat consistent misfire/limp mode while wot 3rd-4th gear 3k rpms plugs were changed 6k miles ago along with injectors and hpfp. I have 63k miles without a carbon cleaning, would that be the culprit? anyways i will post some codes when im back in town tomorrow.
	Appreciate 0 Quote

06-30-2012, 06:06 PM	#107
Spun Crankhub Major General 1001 Rep 5,128 Posts Drives: 15 F82 SOLD Join Date: Feb 2012 Location: San Jose, CA iTrader: (66)	Misfire on Cyliner 5 ONLY with tune in the car, no code when tune is out. I have JB3(pulling it again today to do JB4 upgrade.) I am confused why the misfire only on hard pulls, with software, but I can go hard with no tune and not throw a code. What gives?!?
	Appreciate 0 Quote