Hexon RR600's arrived and installed!

Kienvu14 · 02-02-2016, 05:24 PM

Quote:

Originally Posted by rob1024

Quote:

Originally Posted by BuraQ

Everyone's needs and wants are different. Upgrading your turbos does not mean to boost up. Some people upgrade to be more efficient at the same boost level while gaining significantly more power.

20 PSI on stock turbos is not the same as 20 PSI on upgraded turbos.

I will post my dyno numbers with Wedge tune when it's done. Just might show more realistic numbers that can be achieved with a set of these.

Wasn't trying to trash anybody here. Just can't understand any logic behind it. Anyway,good luck with your 20psi dyno.

Seems like you keep saying "wedge" as if BQ is not a part of it. Not sure if you know that BQ and Ken work together....

rob1024 · 02-02-2016, 06:02 PM

Quote:

Originally Posted by Kienvu14

Seems like you keep saying "wedge" as if BQ is not a part of it. Not sure if you know that BQ and Ken work together....

Never dealt with BQ but has been running Wedge tunes for a while. Even run the beastly 15deg BB flash stocked with jb4 couple of years ago. My tunning knowledge is vastly based on what I have learned from Wedge. I have had nothing but positive experience for those couple of years. If it wasn't for him I would probably be still running a jb4. I was advised by him when decided on Hexons about fueling issues with this platform. Otherwise I wouldn't have spent $700 on fuel-it TBI if it wasn't needed.Actually I probably should have bought his PI kit for another 1k extra. Steve from fuel-it 100% confirmed the same concerns when running E mixes with upgraded twins. I guess they both must be wrong.
Anyway good luck to everyone tunning Hexons hopefully we get great numbers with them with or without proper fueling support.

Jklad · 02-02-2016, 06:25 PM

I'm glad op is opting for a reliable daily tune that is not on the bleeding edge. I likely would go the same route to avoid dealing with all the added bs that comes with pushing things to the edge to maintain a reliable daily driver. Thanks op and looking forward to the Dyno.

Sean978 · 02-02-2016, 06:41 PM

Serious question, because i've never ran a Cobb AP.

Can Cobb only store 1 custom map at a time? I mean, I know with MHD when the time comes i'm going to order a daily pump map, and an e60 "kill" map for hoonigan shit and dyno glory.

Kienvu14 · 02-02-2016, 06:49 PM

Quote:

Originally Posted by Sean978

Serious question, because i've never ran a Cobb AP.

Can Cobb only store 1 custom map at a time? I mean, I know with MHD when the time comes i'm going to order a daily pump map, and an e60 "kill" map for hoonigan shit and dyno glory.

You can store more than 1. I have the custom etune with all the oft maps that Cobb offers on it

Kienvu14 · 02-02-2016, 06:58 PM

Example

Sean978 · 02-02-2016, 07:16 PM

Ok ... I was a little confused there.

Rob you saying you're going to be running max effort tune as a daily??

rob1024 · 02-02-2016, 08:56 PM

Quote:

Originally Posted by Sean978

Ok ... I was a little confused there.

Rob you saying you're going to be running max effort tune as a daily??

Yep 100%. This is how I want my power curve to look like at 24psi
Btw it's a standard hybrid turbo DD map and it should make some more hp now with rr600 with bigger exhaust turbine wheel.
http://www.e90post.com/forums/showth...1192348:dance:
Btw. 24psi is by no means a max effort with these. Maybe +27psi would be according to Ken

BQTuning · 02-02-2016, 09:27 PM

Quote:

Originally Posted by Sean978

Serious question, because i've never ran a Cobb AP.

Can Cobb only store 1 custom map at a time? I mean, I know with MHD when the time comes i'm going to order a daily pump map, and an e60 "kill" map for hoonigan shit and dyno glory.

If you don't have a COBB AP already don't even think about going that direction. Just go with MHD

Grand_hustle17 · 02-03-2016, 09:17 AM

Quote:

Originally Posted by rob1024

I will post my dyno numbers with Wedge tune when it's done. Just might show more realistic numbers that can be achieved with a set of these.

Wasn't trying to trash anybody here. Just can't understand any logic behind it. Anyway,good luck with your 20psi dyno.

I totally understand his logic. Personally for me its not to crank up boost. Most the power cant even be laid on the road any damn ways. For me its to get rid of the annoying rattle while gaining power. 520rwhp for me is fine. I dont care what psi that is lol.

rob1024 · 02-03-2016, 02:08 PM

Quote:

Originally Posted by Grand_hustle17

I totally understand his logic. Personally for me its not to crank up boost. Most the power cant even be laid on the road any damn ways. For me its to get rid of the annoying rattle while gaining power. 520rwhp for me is fine. I dont care what psi that is lol.

Standard hybrid turbo Mboost map by Ken runs 24psi
http://www.e90post.com/forums/showth...92348:dance:of boost with supporting mods. Surely his car is able to hook up somehow. That's when boost by gear will come in handy. There is no such a thing as to much power in a sports car. Just ask any racer

Mike@N54Tuning.com · 02-03-2016, 02:59 PM

Quote:

Originally Posted by BuraQ

If you don't have a COBB AP already don't even think about going that direction. Just go with MHD

+1

Mike

nyt · 02-03-2016, 05:30 PM

My coated rr600s got delivered today. Looks good. Need to finish this f'n rotary build and clean up my garage to get the 335 in.

rob1024 · 02-03-2016, 06:58 PM

Quote:

Originally Posted by nyt

My coated rr600s got delivered today. Looks good. Need to finish this f'n rotary build and clean up my garage to get the 335 in.

They do look great even without the thermal coating. If you don't mind what kind of support mods and tune are you planning to run with them ??? Also,what's your fuel and power goals. Thanks.

nyt · 02-03-2016, 08:17 PM

Quote:

Originally Posted by rob1024

They do look great even without the thermal coating. If you don't mind what kind of support mods and tune are you planning to run with them ??? Also,what's your fuel and power goals. Thanks.

Trying not to blow up my XI drivetrain, so will see. Right now its a stage 2 and meth injection. I'll be adding port injection during this upgrade. Might need a stage 3 pump also, not sure. I'm currently running about 25psi on the stockers which puts out massive torque. I'll be rolling this back a bit and hope to make it up on the top end. Shooting for around 600.

Fast35i · 02-03-2016, 08:55 PM

Quote:

Originally Posted by nyt

My coated rr600s got delivered today. Looks good. Need to finish this f'n rotary build and clean up my garage to get the 335 in.

Post a picture we would like to see them

Billit335 · 02-03-2016, 09:08 PM

Damn I'm thinking of pulling the gun of a set of these Hexon RR600!!

rob1024 · 02-04-2016, 08:23 AM

Quote:

Originally Posted by nyt

Trying not to blow up my XI drivetrain, so will see. Right now its a stage 2 and meth injection. I'll be adding port injection during this upgrade. Might need a stage 3 pump also, not sure. I'm currently running about 25psi on the stockers which puts out massive torque. I'll be rolling this back a bit and hope to make it up on the top end. Shooting for around 600.

Wow,you got nice support mods. I would check with Steve about the st3 pump. You will easily get +600whp on e85 without pushing things to much. I decided on st2 lpfp and TBI injection so most likely will end up around 550whp. I also placed preorder for the new MMP full silicone hot side outlets. Should gain some free power from them even on my limited fueling mods. You definitely should look into them. They made free 20-30whp with less boost even on stockers. Price is very reasonable too.

nyt · 02-04-2016, 08:30 AM

Quote:

Originally Posted by rob1024

Wow,you got nice support mods. I would check with Steve about the st3 pump. You will get easily +600whp on e85 without pushing things to much. I decided on st2 lpfp and TBI injection so most likely will end up around 550whp. I also placed preorder for the new MMP full silicone hot side outlets. Should gain some free power from them even on my limited fueling mods. You definitely should look into them. They made free 20-30whp with less boost even on stockers. Price is very reasonable too.

I have the VTT's on order. I got in on the first bunch so will hopefully see it fairly soon.

rob1024 · 02-04-2016, 08:32 AM

Quote:

Originally Posted by Billit335

Damn I'm thinking of pulling the gun of a set of these Hexon RR600!!

Man,pull the trigger. They look great and have a great costumer support by Wayne. The only thing is the wait time. 4-6 weeks on average.

rob1024 · 02-04-2016, 08:41 AM

Quote:

Originally Posted by nyt

I have the VTT's on order. I got in on the first bunch so will hopefully see it fairly soon.

Yeah,they should be simmular gain as they are both full silicone design. Great job man. Can't wait to see your dyno.
Btw. Is Ken going to Etune your car ???
I am thinking dyno tuning log and tune the map accordingly at same time in one day. Got to pay extra for that but I don't have a problem with that. Still cheaper than loosing your driver license while trying to log on the street 10 times to tune the car.
I'd rather give the money to Ken

altostratus · 02-04-2016, 09:24 AM

Quote:

Originally Posted by Fast35i

Post a picture we would like to see them

Mine came yesterday aswell, look great. Still waiting for outlets before the install

image hosting 12mb

02-02-2016, 06:25 PM	#91
Jklad Lieutenant Colonel 422 Rep 1,643 Posts Drives: 2007 335i Coupe Join Date: Nov 2010 Location: Palatine, IL iTrader: (0)	I'm glad op is opting for a reliable daily tune that is not on the bleeding edge. I likely would go the same route to avoid dealing with all the added bs that comes with pushing things to the edge to maintain a reliable daily driver. Thanks op and looking forward to the Dyno. __________________ 2007 E92 335i MT
	Appreciate 0 Quote

02-02-2016, 06:41 PM	#92
Sean978 Private First Class 35 Rep 120 Posts Drives: 2007 335i 6MT SGM Join Date: Jan 2014 Location: Nashua, NH iTrader: (0)	Serious question, because i've never ran a Cobb AP. Can Cobb only store 1 custom map at a time? I mean, I know with MHD when the time comes i'm going to order a daily pump map, and an e60 "kill" map for hoonigan shit and dyno glory.
	Appreciate 0 Quote

02-02-2016, 06:58 PM	#94
Kienvu14 Second Lieutenant 47 Rep 271 Posts Drives: 07' E90 N54 Aspen White Join Date: Dec 2012 Location: Denver iTrader: (1)	Example Attached Images __________________ E90 - N54 2007 Alpine White FBO : VRSF CP w/ Tial BOV,VRSF 7 inch FMIC, VRSF Catless DP's, Hexon RR600, Cobb V3, VMR V710 Gunmetal 19x8.5 and 19x9.5, SteveAZ stage 2 bucket
	Appreciate 0 Quote

02-02-2016, 07:16 PM	#95
Sean978 Private First Class 35 Rep 120 Posts Drives: 2007 335i 6MT SGM Join Date: Jan 2014 Location: Nashua, NH iTrader: (0)	Ok ... I was a little confused there. Rob you saying you're going to be running max effort tune as a daily??
	Appreciate 0 Quote

02-03-2016, 05:30 PM	#101
nyt Second Lieutenant 128 Rep 256 Posts Drives: 2010 335xi Join Date: Aug 2014 Location: Long Island, NY iTrader: (0)	My coated rr600s got delivered today. Looks good. Need to finish this f'n rotary build and clean up my garage to get the 335 in.
	Appreciate 0 Quote

02-03-2016, 09:08 PM	#105
Billit335 Private First Class 35 Rep 152 Posts Drives: 07 335 Join Date: Aug 2014 Location: Texas iTrader: (1)	Damn I'm thinking of pulling the gun of a set of these Hexon RR600!!
	Appreciate 0 Quote