[jessejericho]

Originally Posted by Southtown

Yes, they look very OEM. It’s made out of a flexible rubber so it contures to the wheel well nicely.

Thanks, just ordered.

[xtougher]

Originally Posted by Southtown

I think the flaps help more than the side skirts. The side skirts might negate some debris but not nearly as much.

Makes sense! Especially with how low you are...not even a lot of opportunity for stuff to get kicked up from below!!

[GregW / Oregon]

So as I posted previously, with the 19x9.5"+5 VT Forged SL-As and 285/35s up front at stock ride height I was getting rubbing on the fender liner at not quite full lock which made very rude and embarrassing sounds. It was enough to break the plastic louvers on one side. The rubbing is confined to a small area near the outside of the liner and I considered doing a mod myself but did not have the bandwidth right now, so I got the very expensive RKP modified liners from IND.

The following photos show 1) & 2) the area of rubbing, 3) the new liners, 4) using a heat gun and dolly to bend the ridged area, 5) the wheel well with liner removed, and 6) new liner in place.

The result was successful, but there is still only about a millimeter clearance at that raised ridge area, but slight contact is not going to hurt anything. I am concerned that the open mesh of the new liner is going to let more debris through coming off the tire compared the the angled louvers.

[IND-Distribution]

Originally Posted by GregW / Oregon

So as I posted previously, with the 19x9.5"+5 VT Forged SL-As and 285/35s up front at stock ride height I was getting rubbing on the fender liner at not quite full lock which made very rude and embarrassing sounds. It was enough to break the plastic louvers on one side. The rubbing is confined to a small area near the outside of the liner and I considered doing a mod myself but did not have the bandwidth right now, so I got the very expensive RKP modified liners from IND.

The following photos show 1) & 2) the area of rubbing, 3) the new liners, 4) using a heat gun and dolly to bend the ridged area, 5) the wheel well with liner removed, and 6) new liner in place.

The result was successful, but there is still only about a millimeter clearance at that raised ridge area, but slight contact is not going to hurt anything. I am concerned that the open mesh of the new liner is going to let more debris through coming off the tire compared the the angled louvers.

Thanks for the write-up and the notes! We have found that the G87 chassis as a whole has had much less of an issue with fender liner clearance in comparison to the G8x M3 & M4 models, but we are glad that you were able to install the RKP liners with 1mm clearance to spare!

[AZG87]

Finally got the 3-piece carbon caps with ZB outer ring added to the SLAs. Subtle but gives a nice accent imo.

[Shizzel720]

Originally Posted by azg87

finally got the 3-piece carbon caps with zb outer ring added to the slas. Subtle but gives a nice accent imo.

🔥🔥🔥

[JCoR]

Originally Posted by AZG87

Finally got the 3-piece carbon caps with ZB outer ring added to the SLAs. Subtle but gives a nice accent imo.

Looking good!

[AZG87]

Originally Posted by JCoR

Looking good!

Thanks! It's not super obvious but adds a nice touch.

[whatthehuck]

I stopped to snap a couple pics of my ride while doing a shoot for someone else, so it's not a photoshoot level of quality but doesn't look too bad 😁😁

Thanks again to Andy for the great deal on some awesome wheels. Evert time I stop to get gas someone comes up and starts asking me about the wheels now lol

[AndyVTForged]

Loving all the new installed shots!!

[apez]

Originally Posted by k-m2-j442

My wheels will be here on Friday (says UPS), picking up the tires at Tire Rack on Saturday, and have an appt to get them mounted Monday. Then I'm taking them to get ceramic coated before I put them on the car (brake dust man...haha)

k-m2-j442 any updates?

I have been looking forward to seeing these wheels on a G87!

[DrewNewM2]

Originally Posted by whatthehuck

I stopped to snap a couple pics of my ride while doing a shoot for someone else, so it's not a photoshoot level of quality but doesn't look too bad 😁😁

Thanks again to Andy for the great deal on some awesome wheels. Evert time I stop to get gas someone comes up and starts asking me about the wheels now lol

Looks great. Any daytime pics?