High beam not working

_TB_ · 10-11-2016, 02:50 PM

E91, Nov 2007.

The highbeam does not work on any of the headlights. The icon illuminates in the dash - but the lights are still on low beam. I have the adaptive xenons.

If i turn off the lights and pull the stalk - the headlights will turn on low beam, not high.

Am I lucky that it might be a fuse? or am I looking at a much much more expensive problem?

VTECaddict · 10-11-2016, 09:11 PM

Did you get any coding done recently?

When you pull the stalk does it activate the bi-xenon shutter or just fires the xenons? What happens when you push the stalk forward with the low beams on?

_TB_ · 10-15-2016, 12:51 PM

No coding done recently. Nothing happens when either pushing or pulling the stalk.

_TB_ · 10-16-2016, 10:00 AM

Checked the fuses - I cannot see anything wrong. The two 40AMP fuses were nto blown (84+86)

Now what to do?

Tim603 · 10-20-2016, 12:45 PM

There is a little electric motor inside the headlight that controls the flapper. If the fuse is ok then that motor could be burnt out.

Unfortunately this part is not available separately however it is not common to burn out so it may be something else, unless you got water in your headlight.

_TB_ · 10-20-2016, 02:53 PM

Quote:

Originally Posted by Tim603

There is a little electric motor inside the headlight that controls the flapper. If the fuse is ok then that motor could be burnt out.

Unfortunately this part is not available separately however it is not common to burn out so it may be something else, unless you got water in your headlight.

I *hope* it is a fuse or a broken wire - since it is both headlights that are not working. If the selenoid/motor had burnt out, I'd suspect only one of them not working.

Do you know what pin in the plug gives the signal to the selenoid?

Tim603 · 10-20-2016, 03:16 PM

Quote:

Originally Posted by _TB_

I *hope* it is a fuse or a broken wire - since it is both headlights that are not working. If the selenoid/motor had burnt out, I'd suspect only one of them not working.

Do you know what pin in the plug gives the signal to the selenoid?

Good point, most likely not the motor then. Not sure about which pin it is sorry. First time I have heard of anyone having this issue

_TB_ · 10-21-2016, 02:16 PM

Funny Thing.. I hooked up the laptop and ran Rheingold. No errors. I can activate the high beam from Rheingold just fine, but nothing happens when pulling the stalk, apart from the blue icon.

Wtf!?

_TB_ · 10-23-2016, 08:22 AM

I just read the NFRM - it is here: https://cloud.catcams.dk/public.php?...d0c5f61b24a13d

Can anybody see anything wrong in it? I can activate the high beam in Rheingold - so the selenoids are working and the wiring must be intact. But I cannot activate the high beam from the stalk. I'm really going insane now..

_TB_ · 01-05-2017, 02:50 PM

Just an update - problem solved by reseting the shor circuit counter. Apparently the bixenon shutter is not reset with the same job as the other SC counters..

kisarci · 01-14-2017, 09:39 PM

How do you reset the short circuit counter? I am having this same exact issue.

_TB_ · 01-15-2017, 02:16 AM

Use "steuern_reset_kurzschlussabschaltung"with the name (yes, the string) from Lampeninfo and not the index like you would with "_reset_kurzschluss_sperre".

kino1161 · 06-11-2024, 07:30 AM

I know this is old, but I am having the same issue. Can I reset the short circuit counter with BMW Protools?

fodder031 · 08-24-2024, 05:09 PM

Quote:

Originally Posted by kino1161

I know this is old, but I am having the same issue. Can I reset the short circuit counter with BMW Protools?

Same issue here. Anyway to reset without coding?

10-11-2016, 02:50 PM	#1
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	High beam not working E91, Nov 2007. The highbeam does not work on any of the headlights. The icon illuminates in the dash - but the lights are still on low beam. I have the adaptive xenons. If i turn off the lights and pull the stalk - the headlights will turn on low beam, not high. Am I lucky that it might be a fuse? or am I looking at a much much more expensive problem?
	Appreciate 0 Tweet Quote

10-11-2016, 09:11 PM	#2
VTECaddict Where'd my VTEC go? 486 Rep 6,066 Posts Drives: 06 330i 6MT Join Date: Mar 2009 Location: Seattle, WA iTrader: (4)	Did you get any coding done recently? When you pull the stalk does it activate the bi-xenon shutter or just fires the xenons? What happens when you push the stalk forward with the low beams on? __________________ AW/Terra \| ZSP \| ZPP \| ZCW \| iDrive \| CA Mods: BC BR coilovers \| Blacklines \| M-tech rear \| dual exhaust \| M3 steering wheel \| BMW SSK \| ZHP shift knob \| High-kick CF spoiler \| NBT Retrofit M3 front control arms \| M3 rear guide rods \| Manzo rear toe and camber links \| Monroe rear shock mounts \| Varrstoen ES1 19x9.5+20 Front, 19x11+25 rear
	Appreciate 0 Quote

10-15-2016, 12:51 PM	#3
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	No coding done recently. Nothing happens when either pushing or pulling the stalk.
	Appreciate 0 Quote

10-16-2016, 10:00 AM	#4
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	Checked the fuses - I cannot see anything wrong. The two 40AMP fuses were nto blown (84+86) Now what to do?
	Appreciate 0 Quote

10-20-2016, 12:45 PM	#5
Tim603 Colonel 487 Rep 2,283 Posts Drives: 2007 335i E90 Join Date: Feb 2012 Location: North Canton, OH iTrader: (8) Garage List 2007 335i [0.00]	There is a little electric motor inside the headlight that controls the flapper. If the fuse is ok then that motor could be burnt out. Unfortunately this part is not available separately however it is not common to burn out so it may be something else, unless you got water in your headlight. __________________ Build Thread
	Appreciate 0 Quote

10-21-2016, 02:16 PM	#8
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	Funny Thing.. I hooked up the laptop and ran Rheingold. No errors. I can activate the high beam from Rheingold just fine, but nothing happens when pulling the stalk, apart from the blue icon. Wtf!?
	Appreciate 0 Quote

10-23-2016, 08:22 AM	#9
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	I just read the NFRM - it is here: https://cloud.catcams.dk/public.php?...d0c5f61b24a13d Can anybody see anything wrong in it? I can activate the high beam in Rheingold - so the selenoids are working and the wiring must be intact. But I cannot activate the high beam from the stalk. I'm really going insane now..
	Appreciate 0 Quote

01-05-2017, 02:50 PM	#10
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	Just an update - problem solved by reseting the shor circuit counter. Apparently the bixenon shutter is not reset with the same job as the other SC counters..
	Appreciate 0 Quote

01-14-2017, 09:39 PM	#11
kisarci Lieutenant 67 Rep 434 Posts Drives: 2007 335i Join Date: Dec 2014 Location: Long Island, NY iTrader: (0)	How do you reset the short circuit counter? I am having this same exact issue. __________________ 07 335i e92
	Appreciate 0 Quote

01-15-2017, 02:16 AM	#12
_TB_ Lieutenant 150 Rep 436 Posts Drives: E91 325d Touring Join Date: Jul 2015 Location: Denmark iTrader: (0)	Use "steuern_reset_kurzschlussabschaltung"with the name (yes, the string) from Lampeninfo and not the index like you would with "_reset_kurzschluss_sperre".
	Appreciate 0 Quote

06-11-2024, 07:30 AM	#13
kino1161 New Member 0 Rep 7 Posts Drives: 2007 328i and 328xi Join Date: Nov 2021 Location: Virginia iTrader: (0)	I know this is old, but I am having the same issue. Can I reset the short circuit counter with BMW Protools?
	Appreciate 0 Quote