[Dazzl]

I have been battling with rough idle and nearly no power about a month.

Everything started with recently purchased e92 2007/07 with N52K. Going over 4K revs I was getting a missfire code and very rough idle

• 29CF DME: Combustion Missfires, Cylinder 3
• Exaust VANOS Mechanism 2A87 DME

Cleaned VANOS, reset engine adaptations, codes were gone until I hit highway and they always come back. Turing car on and off fixed issues for another 10 minutes. Also when starting, car has very strong unburned petrol smell every time.

I bough aftermarked VANOS Solenoids and reset adaptations, and the Vanos 2A87 code dissapeared but the idle suddenly was so bad engine was stalling and car barely drove. I though there was fault with non-oem ones so I plugged back original and idle was instantly better on cold but started to have very rought idle was warmer . Also I suddenly noticed new code that appeared randomly

• P0015 Camshaft Position - Timing Over-Retarded Bank 1

While waiting for OEM Vanos in one of the tests engine started shaking very badly, check engine came up and whole car started pouring petrol out of exaust as it smelled of petrol everywhere and my tank suddenly dropped 1/6 of section in 4 minutes
Errors that appeared

• 2C3D DME: Oxygen sensor Before Catalytic Converter: Line Fault
• 29D9 Missfire at Low Tank
• 2C7B DME: Oxygen sensor after Catalytic Converter
• 2A87 - Exaust Vanos

I had error of post cat lambda before but I changed lambda sensor and until this moment I never had the same issue. After resetting codes same lambda errors never came back.

I tried most popular solutions
I changed new oil, changed old filer and made sure o-rings are correctly attached. Old oild was really bad and old filter detached from oilcap when I took it out and previous owner did not install small o ring correctly on filter
I installed OEM Vanos solenoids and suddenly the idle was really bad instantly (unlike when old solenoids are installed, car works fine for a while) When I installed solenoids and tried to run a car for a while I suddenly had strong vibrations and new codes appeared - -P1632 Throttle Valve Adaptation, Adaptation Conditions not met but Im guessing i started a car too early before adaptations were not finished and car was not in sleep mode. Also previous -P0015 B Camshaft position - Timing over retarded Bank 1 and something new -00,05,14,17(P1417) Please Refer to manual.
I cleaned MAF and tried to locate If I had air leak but couldn't seem to find any
When disconnecting MAF I couldn't tell if anything changed since with the very rought idle seemed random to shake engine randomly.
Tomorrow I'll check VANOS Valves to see if they are dirty but I'm out of ideas after that

[Dazzl]

gbalthrop
edit: I have inpa & ista available

[Dazzl]

Anyone able to assist? I I am completely out of ideas, feels like I've tried everything that culd be inderectly affecting it

I managed to get rid of VANOS exaust code but it sometimes popped back. Now I only mostly have P0015 code "B Camshaft Position - Timing Over-Retarded Bank 1"

Now idle is so rough on cold that car even stalls sometimes but when it warms up, the idle is perfect, however the performacne is really sluggish after 2nd gear and barely drives. check engine pops for a second and dissapears from dashboard. P00150 error shows in ecu. I tried swapping camshaft sensors and I had P0016 code for A Camshaft position bank 1 appearing once and then dissapearing and never showing again.

Extra steps I've taken so far

Swapped OEM Vanos solenoids

Cleaned VANOS filters

I had a missfire in 3rd cylinder at the start stage so I swapped new oem coil

New OEM Map

New OEM Maf

Swapped camshaft sensors intake to outtake but P0015 still persists.



During testing I had some extra codes popping sometimes, they might be less related during some sensors being replugged, but most commons were:

2A9A DME: Crankshaft - Inlet Camshaft, Synchrinization

P113 Intake Air temp sensor 1, circuit high bank 1

P00BD - AirFlow too high



When idle was really rought, settings for Ignition Timing Advance ffor #1 Cylinder was jumping from -4500BTDC to 3000 BTDC and when car is working fine it's around 0



I used ISTA to reset adaptations,



I know there have been a recall for VANOS bolts snapping for N52 but seems behicles from 2009 are affected. Mine is 2007/08.



Does anyone has any ideas? I have a feeling I have tried everything there can be on forums.