HP Autowerks Adjustable Swaybar Endlinks

HP Autosport · 12-15-2009, 04:07 PM

When you lower the vehicle, the swaybar is moved from the ideal factory geometry to an offset that decreases the ability of the swaybar to perform. The swaybar frame mount and the end of the bar should be on the same horizontal plane. The factory endlinks are a solid piece. When the car is lowered, the OEM links cannot compensate for the longer length needed to keep the swaybar in its ideal location. Get immediate response from your sway bar and precise control over your suspension. What this means to you is tighter, more responsive handling.

HP Autowerks is happy to introduce adjustable endlinks. With adjustable endlinks you can return the bar to its ideal leverage point while lowered. They also afford the peace of mind that the links or shock link mount will not fail as is common in factory units, as they will now be adjusted properly. The links are adjustable in length up to an additional 1.25" over stock. HP Autowerks end links are adjustable while on the vehicle.

These end links will fit the following vehicles:
E9x 3-Series Front (no-xi)
E82 3-Series Front

http://www.hpashop.com/product.sc?pr...categoryId=119

$155.99 pair

Alan l. · 12-18-2009, 11:09 PM

Would these work with FK coilovers? Any warranty on these?

Alan

HP Autosport · 12-18-2009, 11:16 PM

Quote:

Originally Posted by Alan l.

Would these work with FK coilovers? Any warranty on these?

Alan

Does your stock one work on the FK coilovers? What is different with the FK coilover system that don't allow these endlink kit to work?

These are over engineered. If any failure should occur, it will be from improper installation and length adjustment.

Alan l. · 12-18-2009, 11:40 PM

I didn't do the install but the difference of the oem ones vs the fk endlinks is the length. Not sure what else is different though.

HP Autosport · 12-18-2009, 11:50 PM

Quote:

Originally Posted by Alan l.

I didn't do the install but the difference of the oem ones vs the fk endlinks is the length. Not sure what else is different though.

That is what I figured. These are made just for that purpose and is adjustable for up to 1 1/4" longer than oem.

Alan l. · 12-19-2009, 01:21 AM

So when you lower a vehicle, you need longer end links? For some reason i thought it was the other way around.

HP Autosport · 12-19-2009, 11:21 AM

Quote:

Originally Posted by Alan l.

So when you lower a vehicle, you need longer end links? For some reason i thought it was the other way around.

Yes, longer.

What you are trying to do is to bring the anti roll bar back to its original geometry, at least as close as you can for the anti roll bar to work more efficiently.

extraboost · 12-19-2009, 05:12 PM

Quote:

Originally Posted by HP Autowerks

That is what I figured. These are made just for that purpose and is adjustable for up to 1 1/4" longer than oem.

the fk endlinks are about that 1 1/4" shorter

HP Autosport · 12-21-2009, 12:53 AM

Quote:

Originally Posted by extraboost

the fk endlinks are about that 1 1/4" shorter

To accomodate the much lower anti roll bar endlink mounting point on the front struts.

However, you may actually need endlinks of stock length to bring the geometry back.

ontopofm · 12-21-2009, 01:33 PM

Quote:

Originally Posted by HP Autowerks

To accomodate the much lower anti roll bar endlink mounting point on the front struts.

However, you may actually need endlinks of stock length to bring the geometry back.

will the endlinks bend or break if you use the stock length? or maybe damage something else?

cn555ic · 12-21-2009, 01:36 PM

Quote:

Originally Posted by HP Autowerks

To accomodate the much lower anti roll bar endlink mounting point on the front struts.

However, you may actually need endlinks of stock length to bring the geometry back.

My question is should I get the OEM ones or buy the ones that are adjustable...My passenger side endlink from my FK coilover kit seems to be broken because everytime I turn the wheel all the way to the right, there is a clank/clunk noise at that same exact point in turning of wheel, if I turn it back the other direction the same noise and vice versa....Its strange that it only happens when the wheel is turned almost fully to the right at the certain turn point...What do you suggest??

HP Autosport · 02-05-2010, 05:45 PM

Quote:

Originally Posted by cn555ic

My question is should I get the OEM ones or buy the ones that are adjustable...My passenger side endlink from my FK coilover kit seems to be broken because everytime I turn the wheel all the way to the right, there is a clank/clunk noise at that same exact point in turning of wheel, if I turn it back the other direction the same noise and vice versa....Its strange that it only happens when the wheel is turned almost fully to the right at the certain turn point...What do you suggest??

I think you will fine the oem links to be about 1" too longe.

The FK needs shorter than stock endlinks. A few forum members already contacted me and custom length for the FK coilovers will be ready to ship the middle of next week.

nguyen · 02-05-2010, 09:53 PM

thanks for your help harold, cant wait to get them for my FK's

HP Autosport · 02-05-2010, 10:51 PM

Quote:

Originally Posted by nguyen

thanks for your help harold, cant wait to get them for my FK's

Please pass it on to Motorwerks.

I335 · 02-06-2010, 08:12 AM

Hey Harold,

Would you recommend these with KW Street Comforts? I have no idea if I need longer ones or shorter ones with my setup. I also have H&R sways if that makes a difference. What's your recommendation? Thx!

HP Autosport · 02-06-2010, 11:48 AM

Quote:

Originally Posted by I335

Hey Harold,

Would you recommend these with KW Street Comforts? I have no idea if I need longer ones or shorter ones with my setup. I also have H&R sways if that makes a difference. What's your recommendation? Thx!

With most aftermarket struts and coilover systems you will need longer links to bring the anti roll bar back to the ideal geometry. It also depends on how far you have lowered your car.

What you are trying to achieve is for the anti roll bar endlink mounting point to be as close to the same plane as the center mounting bushings without the joints being stressed(pivot excessively). The best way to check it is to have your car on a drive-on lift that way all 4 wheels are loaded, disconnect the endlinks and determine what you need.

Most of the cases, 1-1.25" longer is what you will need.

Harold

mastermayhm · 02-17-2010, 12:11 PM

how much shipped to 46236?

HP Autosport · 02-17-2010, 12:32 PM

Quote:

Originally Posted by mastermayhm069

how much shipped to 46236?

About $9

T7R_Sky · 04-26-2010, 01:09 AM

Hey. I just installed some KW Clubsports and I definitely need new endlinks! Would I have to order 2 sets of endlinks (1 for front and 1 for back) or just one set for the front? (I dont know how the rear swaybar is supposed to sit ideally) And I dont know what the length I would need is either. I'm doing it all myself in my garage so I need all the help I can get. Thanks!

I335 · 06-06-2010, 05:05 PM

Quote:

Originally Posted by T7R_Sky

Hey. I just installed some KW Clubsports and I definitely need new endlinks! Would I have to order 2 sets of endlinks (1 for front and 1 for back) or just one set for the front? (I dont know how the rear swaybar is supposed to sit ideally) And I dont know what the length I would need is either. I'm doing it all myself in my garage so I need all the help I can get. Thanks!

Good question...

twinship · 06-22-2010, 09:54 PM

Harold--

2 questions:

1) Do I need these in conjunction with H&R Sport springs?

2) What's the estimated install time for these?

Thx!

onefastman · 06-25-2010, 11:03 AM

What would I need with JIC/Cross?

12-15-2009, 04:07 PM	#1
HP Autosport Supreme Allied Commander 4089 Rep 55,797 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, AP, Brembo, GIAC, Koni, Ohlins, Performance Friction, www.hpautosport.com iTrader: (36)	HP Autosport Adjustable Swaybar Endlinks When you lower the vehicle, the swaybar is moved from the ideal factory geometry to an offset that decreases the ability of the swaybar to perform. The swaybar frame mount and the end of the bar should be on the same horizontal plane. The factory endlinks are a solid piece. When the car is lowered, the OEM links cannot compensate for the longer length needed to keep the swaybar in its ideal location. Get immediate response from your sway bar and precise control over your suspension. What this means to you is tighter, more responsive handling. HP Autowerks is happy to introduce adjustable endlinks. With adjustable endlinks you can return the bar to its ideal leverage point while lowered. They also afford the peace of mind that the links or shock link mount will not fail as is common in factory units, as they will now be adjusted properly. The links are adjustable in length up to an additional 1.25" over stock. HP Autowerks end links are adjustable while on the vehicle. These end links will fit the following vehicles: E9x 3-Series Front (no-xi) E82 3-Series Front http://www.hpashop.com/product.sc?pr...categoryId=119 *$155.99 pair* Attached Images Last edited by HP Autosport; 12-10-2016 at 01:36 PM..
	Appreciate 0 Tweet

12-18-2009, 11:09 PM	#2
Alan l. Major General 5750 Rep 9,020 Posts Drives: 2020 F95 X5M Competition Join Date: Jun 2009 Location: United States iTrader: (9)	Would these work with FK coilovers? Any warranty on these? Alan __________________
	Appreciate 0

12-18-2009, 11:40 PM	#4
Alan l. Major General 5750 Rep 9,020 Posts Drives: 2020 F95 X5M Competition Join Date: Jun 2009 Location: United States iTrader: (9)	I didn't do the install but the difference of the oem ones vs the fk endlinks is the length. Not sure what else is different though. __________________
	Appreciate 0

12-19-2009, 01:21 AM	#6
Alan l. Major General 5750 Rep 9,020 Posts Drives: 2020 F95 X5M Competition Join Date: Jun 2009 Location: United States iTrader: (9)	So when you lower a vehicle, you need longer end links? For some reason i thought it was the other way around. __________________
	Appreciate 0

02-05-2010, 09:53 PM	#13
nguyen Private First Class 8 Rep 182 Posts Drives: 2006 BMW 330i Join Date: Aug 2009 Location: Houston, Tx iTrader: (6)	thanks for your help harold, cant wait to get them for my FK's
	Appreciate 0

02-06-2010, 08:12 AM	#15
I335 Brigadier General 126 Rep 4,248 Posts Drives: '08 335i Coupe Join Date: Jan 2008 Location: New England iTrader: (11)	Hey Harold, Would you recommend these with KW Street Comforts? I have no idea if I need longer ones or shorter ones with my setup. I also have H&R sways if that makes a difference. What's your recommendation? Thx!
	Appreciate 0

02-17-2010, 12:11 PM	#17
mastermayhm Brigadier General 275 Rep 4,773 Posts Drives: F90 M5 Join Date: Sep 2008 Location: INPLS, IN iTrader: (13)	how much shipped to 46236? __________________ e90 330 > e90 LCI N54 > e70 x5 50i > f12 M6 GC > f15 x5 50i > f90 M5
	Appreciate 0

04-26-2010, 01:09 AM	#19
T7R_Sky "I know you know that I know you know..." 25 Rep 795 Posts Drives: Sparkling Graphite E90 328i Join Date: Mar 2006 Location: Escondido, CA iTrader: (3) Garage List 2008 E90 328i [0.00]	Hey. I just installed some KW Clubsports and I definitely need new endlinks! Would I have to order 2 sets of endlinks (1 for front and 1 for back) or just one set for the front? (I dont know how the rear swaybar is supposed to sit ideally) And I dont know what the length I would need is either. I'm doing it all myself in my garage so I need all the help I can get. Thanks! Last edited by T7R_Sky; 04-26-2010 at 10:01 AM..
	Appreciate 0

06-22-2010, 09:54 PM	#21
twinship Booosted 48 Rep 832 Posts Drives: 2008 335i Join Date: Nov 2009 Location: Los Angeles iTrader: (3) Garage List 2008 335i [0.00]	Harold-- 2 questions: 1) Do I need these in conjunction with H&R Sport springs? 2) What's the estimated install time for these? Thx! __________________ 2008 BMW 335i//Jet Black on Black Dakota Leather//Steptronic, Sport Package, Premium Package, Logic7 Sound, Aluminum Trim, iPOD & USB, Cobb S1+ Sport, ER FMIC, ER CP, K&N Filter, H&R Sport Springs, Koni Yellows, ECS Tuning spacers (F-10mm/R-15mm), Akebono pads, OEM Rear Aero Spoiler, OEM Sport Diffusor, Cyba 3.8" Tips, OEM Aluminum Pedals, M-tech Steering Wheel, Clear Reflectors
	Appreciate 0

06-25-2010, 11:03 AM	#22
onefastman Major General 162 Rep 5,689 Posts Drives: 2009 135i 2011 e92m dct Join Date: Sep 2009 Location: Earth iTrader: (15)	What would I need with JIC/Cross? __________________ Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(1addicts.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
	Appreciate 0