[Madnking]

2012 e92 n55
I have the over heating problem with my Fuel Control Module/EKP. My car would just stall and would not restart until the module cooled down enough. I contacted FCP Euro for a proper replacement part number. I then found a used one at the local parts yard and installed the module. It runs fine but on start up it does not always prime the lpfp. I have to remove the key re insert and turn the ignition on and listen for the pump. It may come right on or take 10 times but once its running I have no problems. I tried to get the EKP flashed but the programmer gets a error when trying to communicate with the EKP. I am wanting to buy a new one but want to make sure its the EKP before spending $350 and have the same communication problem. Just curious if anyone has had a similar experience. thanks

[Levanime]

you need to code it with ncs

[Madnking]

Originally Posted by Levanime

you need to code it with ncs

yes sir I believe you tried to code it but kept getting a error. I was just trying to figure out if it was because I purchased a used ekp or if I had another problem. I read somewhere but I cant find it now that some one had to install their old ekp copy the vin and then install the new ekp and paste the vin on it?

[sunny_j]

Did you ever figure it out?

[Rcue177]

i need help coding too

[Joe@TopGearSolutions]

Originally Posted by Rcue177

i need help coding too

We can help remotely. Do you have a KDCAN cable already? If not, we can send one.

[Rcue177]

Originally Posted by Joe@TopGearSolutions

We can help remotely. Do you have a KDCAN cable already? If not, we can send one.

yes i have a k dcan ready

[Joe@TopGearSolutions]

Originally Posted by Rcue177

yes i have a k dcan ready

PM sent

[Rcue177]

Originally Posted by Joe@TopGearSolutions

PM sent

hey just leaving some feedback for joe from top gear solutions, maan where do i start. i cannot say how grateful i am to have come across joe, not only did he help me out to code my epkm to my e90 flawlessly but he also welcomed me into the bmw community with open arms. if i ever come across anything else i know exactly who to ask now. Thanks again Joe !

[ianzturn@gmail.com]

Originally Posted by Joe@TopGearSolutions

We can help remotely. Do you have a KDCAN cable already? If not, we can send one.

Are you free to do this for me, i have an ekp installed but i dont think the parameters are correct for the Walbro 450, my EKP does overheat and will shut my car off but my LPFP is only pulling between 28-32 in the JB4 app, when i first installed the pump it was at 64 i think, but then my car sat for a month while i was on a trip and i come back to this madness. Ive tried to lookup how to do it myself with the higher current values but i cant figure out NCS to save my life. I did get a error code on the JB4 for voltage/current too high one time, and i also got a 29F1 fuel pressure plausibility. I do already have a cable.

[mizta insane]

I can help if needed pm me

[shea051702]

Originally Posted by mizta insane

I can help if needed pm me

Hello, I’ve been reading post about the Fuel pump control module and you’re post came up. I was wondering if you can assist me in any way. I purchased a used module out of the same car and engine except the year is 2008 and my car is a 2009 but the engine is the exact same and the model car also. I would like to know if I need to program this used module or will it be plug and play and will everything work or do I need to code it. I do have ncs expert and Inpa but don’t know how to use it. Please offer any insight, thanks.

[shea051702]

Originally Posted by Joe@TopGearSolutions

We can help remotely. Do you have a KDCAN cable already? If not, we can send one.

Hello, I came across you’re post concerning the fuel pump control module and was wondering if you can offer any assistance. I brought a used module that is the exact same, the model car is the same and the engine also. The year is different 2008 module and my car is a 2009. I was wondering if I need to program/ code the module to my car or if it will be plug and play. I would like to know if there is any assistance that you could provide, I have inpa and ncs expert and foxwell nt510 elite if this works. Any assistance you can offer will be helpful.

[aradujk]

Does anyone know if I can use a EKPM3 fuel pump module to replace my EKPM2 on my 2006 325i e90 sedan? I tried to program in NCS and am getting the ERROR MESSAGE: Error in CABD! Look at CABI.ERR and ERROR.LOG!
COAPI-2020: SG antwortet nicht IFH-0009: SG nicht angeschlossen oder meldet sich nicht EKPM60_2
COAPI-2020: SG antwortet nicht CODIERINDEX_LESEN
COAPI-2020: SG antwortet nicht IFH-0009: SG nicht angeschlossen oder meldet sich nicht EKPM60_2
COAPI-2020: SG antwortet nicht SG_CODIEREN

I am running NCS V4.01 CoAPI V3.13.2 KrAPi V3.0.2 and Ediabas V7.3.0
I also am using INPA 5.0.6 to check connection to car.

I am not sure why I keep getting these error messages when I am trying to code the new fuel pump module. Any help would greatly be appreciated. Thanks

[Biggstrapp]

Originally Posted by Rcue177

hey just leaving some feedback for joe from top gear solutions, maan where do i start. i cannot say how grateful i am to have come across joe, not only did he help me out to code my epkm to my e90 flawlessly but he also welcomed me into the bmw community with open arms. if i ever come across anything else i know exactly who to ask now. Thanks again Joe !

So i am new to this fourm and i cant pm anyone yet but I kinda need help recoding my ekpm2 because i kinda clicked on the (set null-code) job in protools expert mode. as of today my car has been down a month because of this issue. i would absolutley appreciate any help here, and yes i have a K-DCAN cable as well i have INPA 5.0, and NCS EXPERT.

[Joe@TopGearSolutions]

Originally Posted by Biggstrapp

So i am new to this fourm and i cant pm anyone yet but I kinda need help recoding my ekpm2 because i kinda clicked on the (set null-code) job in protools expert mode. as of today my car has been down a month because of this issue. i would absolutley appreciate any help here, and yes i have a K-DCAN cable as well i have INPA 5.0, and NCS EXPERT.

Replied to your PM.

[e60moo]

Can someone PLEASE help me out!! im having a similiar issue. Car would turn off when the ekpm3 would overheat and i would have to wait for it to cool down before driving it home. Am i able to order a used ekpm3 and plug and play or do i need to code it ?

[Shadowe92]

Originally Posted by Joe@TopGearSolutions

Replied to your PM.

Sorry to revive a dead thread. Would you be able to help me as well with the programming. I’ve tried numerous times and have been unsuccessful. I do have a the proper cable as well.