[rvegabonilla]

Hi everyone,

I'm towards purchasing an mtech front bumper from jg mods, do I need to buy the guides and ducts (i have a e90 lci non sport)? Or i just need only the bumper? Do you know of any other vendors that ships to Puerto Rico?

[TunerStock]

Originally Posted by rvegabonilla

Hi everyone,

I'm towards purchasing an mtech front bumper from jg mods, do I need to buy the guides and ducts (i have a e90 lci non sport)? Or i just need only the bumper? Do you know of any other vendors that ships to Puerto Rico?

You will need the fender liners, splash shield extender, etc. Since your car did not come factory with M Sport.

Best,
TunerStock

[rvegabonilla]

Originally Posted by TunerStock

You will need the fender liners, splash shield extender, etc. Since your car did not come factory with M Sport.

Best,
TunerStock

In the jg mods site list these parts:

2009-2011 LCI Additional Recommended Parts Needed:

Front Left Brake Air Duct 51747891379
Front Right Brake Air Duct 51747891380
Adapter Under Hood Shield 51117892935
Deflector Lip, Left 51717892697
Deflector Lip, Right 51717892697
Cover, Bottom Left 51717892801
Cover, Bottom Right 51717892802
Adapter 511758040109

Do i need anything else or i'll be fine with only those.

[TunerStock]

Originally Posted by rvegabonilla

In the jg mods site list these parts:

2009-2011 LCI Additional Recommended Parts Needed:

Front Left Brake Air Duct 51747891379
Front Right Brake Air Duct 51747891380
Adapter Under Hood Shield 51117892935
Deflector Lip, Left 51717892697
Deflector Lip, Right 51717892697
Cover, Bottom Left 51717892801
Cover, Bottom Right 51717892802
Adapter 511758040109

Do i need anything else or i'll be fine with only those.

PM your car's VIN, I'll see if I can get the accurate list for your specific vehicle.

[uber]

You can be a cheapo like me and not buy any of those things. The bumper went on fine with my stock fender liner and such.

The bottom of the bumper screws in at two spots though, versus 5. Maybe get the underbody adapter. You can to trim the corner of the fender liner too, but the screw holes line up with the mtech bumper.

[rvegabonilla]

Didn't know you were a vendor.

[rvegabonilla]

Originally Posted by uber

You can be a cheapo like me and not buy any of those things. The bumper went on fine with my stock fender liner and such.

The bottom of the bumper screws in at two spots though, versus 5. Maybe get the underbody adapter. You can to trim the corner of the fender liner too, but the screw holes line up with the mtech bumper.

And it's holding strong? Isn't loose? Did it by yourself or took it to a body shop?

[uber]

Originally Posted by rvegabonilla

And it's holding strong? Isn't loose? Did it by yourself or took it to a body shop?

It's holding strong. Or it was, I just switched bumpers.

The bumper is head on by 4 torx bolts in between the headlights and two fender-bumper bolts. That's your main structure. The underbody bolts aren't essential. If you can get a few in it'll be fine.

Like I said, I got two bolts to line up in the wheel liner and 2 bolts on the under body area. It was good. Didn't flop around or anything.

Try it out, if you eventually want to get all the OEM parts, you should, but for now it's not absolutely required.

[Route 16]

cheapest/laziest way, is to just use whatever is on your current car and switch straight to jgmods bumper
i used all the same bolts/screws at the spots, my bumper is essentially held by the 4 in the middle where the kidney grills are, the 2 by the headlight and the 1 around where the foglight is, i drove it like that with 3 different bumpers and always held on