335xi Ball Joint Bolt Torque

Blaze439 · 04-18-2018, 08:33 PM

Does anyone know the required torque spec for the two bolts that attach the ball joint to the front spindle on my XI? Can't seem to find it online or in the Bentley. Thanks!

frenchi · 04-19-2018, 02:22 AM

80nm to spindle and 100nm + 90 degrees to chassis.

Blaze439 · 04-19-2018, 06:12 AM

Quote:

Originally Posted by frenchi

80nm to spindle and 100nm + 90 degrees to chassis.

Im talking about the two smaller torx head bolts that bolt the ball joint to the spindle. The ball joint is slightly different on an XI meaning its not attached to the thrust arm.

frenchi · 04-19-2018, 09:36 AM

Quote:

Originally Posted by Blaze439

Im talking about the two smaller torx head bolts that bolt the ball joint to the spindle. The ball joint is slightly different on an XI meaning its not attached to the thrust arm.

That’s the one i got XI also

Blaze439 · 04-19-2018, 02:48 PM

Quote:

Originally Posted by frenchi

Quote:

Originally Posted by Blaze439

Im talking about the two smaller torx head bolts that bolt the ball joint to the spindle. The ball joint is slightly different on an XI meaning its not attached to the thrust arm.

That's the one i got XI also

The two bolts shown here

blueloco · 04-19-2018, 10:00 PM

Those are M10 class 10.9. "Guide joint to swivel bearing" 60NM & recut threads. I couldn't get my tap in both holes but chasing the threads does help.

Blaze439 · 04-20-2018, 12:59 PM

Quote:

Originally Posted by blueloco

Those are M10 class 10.9. "Guide joint to swivel bearing" 60NM & recut threads. I couldn't get my tap in both holes but chasing the threads does help.

Thanks!

datbimmer · 04-20-2018, 04:41 PM

I think about 6 bugga buggas should be enough

feuer · 04-20-2018, 08:42 PM

Quote:

Originally Posted by Blaze439

The two bolts shown here

Quote:

Originally Posted by blueloco

Those are M10 class 10.9. "Guide joint to swivel bearing" 60NM & recut threads. I couldn't get my tap in both holes but chasing the threads does help.

Poor design and execution. Very small bolts into a cast iron upright. I had one recently that was butchered by previous tech and rusted too so ended up using a loger bolt with nut. I really don't understand why everything on the xDrive is iron instead of aluminum?

Blaze439 · 04-20-2018, 09:13 PM

Quote:

Originally Posted by feuer

Quote:

Originally Posted by Blaze439

The two bolts shown here

Quote:

Originally Posted by blueloco

Those are M10 class 10.9. "Guide joint to swivel bearing" 60NM & recut threads. I couldn't get my tap in both holes but chasing the threads does help.

Poor design and execution. Very small bolts into a cast iron upright. I had one recently that was butchered by previous tech and rusted too so ended up using a loger bolt with nut. I really don't understand why everything on the xDrive is iron instead of aluminum?

How did you get the ball joint out of the spindle? I got both bolts out... finally..

blueloco · 04-20-2018, 09:51 PM

Quote:

Originally Posted by Blaze439

How did you get the ball joint out of the spindle? I got both bolts out... finally..

My summary from about a month ago;
http://www.e90post.com/forums/showth...1156333&page=4

Need a good air hammer. I don't think I could have got them any other way.

feuer · 04-20-2018, 10:10 PM

Quote:

Originally Posted by Blaze439

How did you get the ball joint out of the spindle? I got both bolts out... finally..

Quote:

Originally Posted by blueloco

My summary from about a month ago;
http://www.e90post.com/forums/showth...1156333&page=4
Need a good air hammer. I don't think I could have got them any other way.

Yes, air chisel (hammer) is the only way.

Blaze439 · 04-21-2018, 02:43 PM

Got one today and finally got it out. What a pain in the nuts

04-18-2018, 08:33 PM	#1
Blaze439 Private First Class 93 Rep 117 Posts Drives: E30 Track Car 335XI Daily Join Date: Mar 2018 Location: Gales Ferry, CT iTrader: (0)	335xi Ball Joint Bolt Torque Does anyone know the required torque spec for the two bolts that attach the ball joint to the front spindle on my XI? Can't seem to find it online or in the Bentley. Thanks!
	Appreciate 0 Tweet Quote

04-19-2018, 02:22 AM	#2
frenchi Lieutenant 92 Rep 452 Posts Drives: F30 340i M Performance Join Date: Nov 2008 Location: France iTrader: (11)	80nm to spindle and 100nm + 90 degrees to chassis.
	Appreciate 0 Quote

04-19-2018, 10:00 PM	#6
blueloco Private 20 Rep 78 Posts Drives: 325xi Join Date: Aug 2017 Location: Alaska iTrader: (0)	Those are M10 class 10.9. "Guide joint to swivel bearing" 60NM & recut threads. I couldn't get my tap in both holes but chasing the threads does help.
	Appreciate 0 Quote

04-20-2018, 04:41 PM	#8
datbimmer Wastegate Rattle 115 Rep 897 Posts Drives: 335i m6t nav sport Join Date: Dec 2013 Location: Canada iTrader: (0)	I think about 6 bugga buggas should be enough __________________ 2007 335i E92 Sport, CIC, 6MT, DOCRACE6266 Spacegray/Black 2009 335i xDrive Black/Black Nav AT Individual Gf: 2011 335i Xdrive Mpack,Nav AT Alpine/SaddleBrown
	Appreciate 1 feuer4289.00 Quote

04-21-2018, 02:43 PM	#13
Blaze439 Private First Class 93 Rep 117 Posts Drives: E30 Track Car 335XI Daily Join Date: Mar 2018 Location: Gales Ferry, CT iTrader: (0)	Got one today and finally got it out. What a pain in the nuts
	Appreciate 0 Quote