|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Brake sensor reset issue
|
|
10-14-2018, 01:12 AM | #1 |
Major General
2770
Rep 6,376
Posts |
Brake sensor reset issue
I put in new rear brake sensor and I reset the change pad warning but the reset KM shows 9 000km? Shouldn'it be like 50 000Km?
|
10-14-2018, 11:59 AM | #4 |
Brigadier General
2455
Rep 4,330
Posts |
sometimes they don't reset properly.
I had to cut the wire to the old one and short the two wires together to get mine to reset. Then install the new sensor. |
Appreciate
0
|
10-14-2018, 12:01 PM | #5 | |
Major General
2770
Rep 6,376
Posts |
Quote:
To give you a example of what happened tho maybe it's related: I had installed my first sensor and reset it when I did the brake pad but I wasn't able to fit it in properly so left it outside the brake pad. Eventually it fell and broke the sensor part so I drove on the replace brake pad warning for about 1000 KM. Yesterday put in my new sensor properly, reset it and that's when it showed 9 000KM until replacement. |
|
Appreciate
0
|
10-14-2018, 09:09 PM | #7 |
Major General
2770
Rep 6,376
Posts |
|
Appreciate
0
|
10-14-2018, 10:00 PM | #8 |
Private
8
Rep 76
Posts |
Yea I am confused here to, maybe there is a DIY but I didn't realize I would need one. I am in the process of putting new pads/rotors/abs and brake sensors on my car. What all programming will I need to do?
I have already replaced the rear brake sensor and have driven the car since, that was the sensor that went off to prompt the pad change. The brake light is still on, what do I need to do to get rid of it? |
Appreciate
0
|
10-14-2018, 10:08 PM | #9 | |
Major General
2770
Rep 6,376
Posts |
Quote:
You do need to reset it for sure. In my case though don't know why second reset has put it only to 9000 even though I have a brand new sensor. |
|
Appreciate
0
|
10-15-2018, 12:21 PM | #10 | |
Brigadier General
2455
Rep 4,330
Posts |
Quote:
why is it you start threads and ask for advice and then question every solution that's given? use the search function like I did, find the same solution I gave you used by multiple people to solve the same issue we both had and then go do it. |
|
Appreciate
0
|
10-15-2018, 01:23 PM | #11 | |
Major General
2770
Rep 6,376
Posts |
Quote:
And I'm question because I want to know why. What's the point in having a solution without knowing the reason or logic behind it, you're not learning anything that way. And I still don't understand why me resetting the service with a brand new sensor doesn't reset it And F searching, honestly this is a forum. I really don't get this searching logic, how can someone get so sick of just answering a issue. Don't want to answer it don't participial. If they are no sticky I really don't see why I should force in searching. And hell, I did search on google and I haven't find again, why it resets to 9K Km with a brand new sensor. Why do I need to short my old sensor? First time I put in a new sensor it worked perfect. Hopefully this answers your question? |
|
Appreciate
0
|
10-15-2018, 01:45 PM | #12 | |
Colonel
454
Rep 2,973
Posts |
Quote:
Jut changing the sensor will not reset the distance. You need tell the car the brakes and sensor changed by coding.
__________________
Arctic Metallic\CF Splitters, Spoiler, Mirror Covers\LED Tails\LSD\Tinted\Coded\Apex Square SM10-19"\LED Angel Eyes\Gloss Black Grill\Integrated V1 & Galaxy Tab\M-Performance Brakes\Cobb Tuned\xHP Flash\Resonator Removed and -> is your friend.
|
|
Appreciate
0
|
10-15-2018, 02:02 PM | #13 |
Major General
2770
Rep 6,376
Posts |
I reset the sensor through the dash. If you hold the trip button you can choose which service indicator to reset. Like I did the first time it worked and same for my oil change.
|
Appreciate
0
|
10-15-2018, 02:46 PM | #14 | |
Brigadier General
2455
Rep 4,330
Posts |
Quote:
I gave you the solution. Short the two pins and reset it. install your new sensor afterwords. If you bothered to search you would find all of the relevant technical information on why this works. but good luck getting someone to spoon feed you the information that you're too lazy to go and find on your own. |
|
Appreciate
0
|
10-15-2018, 03:50 PM | #15 | |
Major General
2770
Rep 6,376
Posts |
Quote:
And no, I think you are actually wrong. The system thinks because of how fast my new sensor got triggered, it thinks that I'm using rear brake pads every 9k. My 9K has not moved from where it was yet. You have still yet to explain me why it would reset to 9K instead of 50k so I think that's why. |
|
Appreciate
0
|
10-15-2018, 03:53 PM | #16 |
Major General
2770
Rep 6,376
Posts |
|
Appreciate
0
|
10-16-2018, 06:44 PM | #17 | |
Colonel
454
Rep 2,973
Posts |
Quote:
If you try to reset a sensor a second time, chances are it will fail and you will get a red dash light for pads. If you short the wires in the connector you can reset the system and reuse the old/previously programmed sensor. Not sure what to do. Maybe car is confused on your brake wear.
__________________
Arctic Metallic\CF Splitters, Spoiler, Mirror Covers\LED Tails\LSD\Tinted\Coded\Apex Square SM10-19"\LED Angel Eyes\Gloss Black Grill\Integrated V1 & Galaxy Tab\M-Performance Brakes\Cobb Tuned\xHP Flash\Resonator Removed and -> is your friend.
|
|
Appreciate
0
|
10-16-2018, 07:56 PM | #18 | |
Major General
2770
Rep 6,376
Posts |
Quote:
I will just wait it out and I guess reset when it hits 0 because it will most definitely not be used. |
|
Appreciate
0
|
10-17-2018, 09:15 AM | #19 | |
Second Lieutenant
107
Rep 202
Posts |
You don't have any direct control over what the CBS indicator will display upon resetting the brake service items. The computer will calculate and display a new value based on a previously stored value. Here it is directly from the BMW TIS:
Front and rear brake pads The condition of the brake pad is determined by the DSC control unit. The calculation is based on a signal from the brake pad wear sensors at 2 points (4 mm and 6 mm). Quote:
You've done the work (properly), replaced the sensor (properly), and reset the CBS item (properly). The computer will start counting down that mileage, but won't "know" that it gave an inaccurate estimate until the 1st stage wear signal isn't triggered in 9,000 km. In 9,000 km (or likely some ~1,000 km sooner), the countdown will be stopped until the 1st stage wear sensor is triggered at which point the computer will have some valuable data with which to revise its estimate. I can't say for sure if the CBS will display a higher value immediately upon "learning" the new estimate, or if that value gets stored for future use at the next reset. Sorry for the long post, but hopefully it gives you a little more insight as to what's going on. Just know you didn't do anything "wrong"...other than maybe replace the brake pads early and confuse a dumb computer. |
|
Appreciate
1
TheMidnightNarwhal2769.50 |
10-17-2018, 09:40 AM | #20 | |
Major General
2770
Rep 6,376
Posts |
Quote:
Thank you so much confirms it now for sure. It saw my last sensor get completely used up within 3 000 KM lol |
|
Appreciate
0
|
10-17-2018, 10:07 AM | #21 |
Second Lieutenant
107
Rep 202
Posts |
No problem. I think it's really only an issue for those of us with a touch of OCD because we want ze numbers to be uber-accurate.
The system works perfectly for those folks who rely on the lights on the dashboard to schedule their service. Those of us who do early preventative maintenance...not so much. |
Appreciate
0
|
10-17-2018, 12:04 PM | #22 | |
Major General
2770
Rep 6,376
Posts |
Quote:
For me I want to keep it so my car stays like... OEM I guess, like it came out of the factory. Like I won't just base if they need replacing on that but it's a good reminder for when to take a look at your pads I guess. |
|
Appreciate
0
|
Bookmarks |
|
|