Shutter e91 does not work oem.

wortel55 · 10-15-2021, 04:08 PM

Shutter e91 does not work oem
Hello, i´m Bern from Holland and I drive a 381i LCI e91.2010. I replaced my halogens for LCI oem bi´xenon's. Made the oem wire change. Earth on pin 2 of the headlight connector and the shutter wire from pin 5 hl connector to pin 41 of my frm module the PL2 FRM II (LED,NSW) date 0609.
Coded the CAS VO and FRM VO ( Add $522) and re-coded the FRM with the code data. I added the TRC code data in a attachment. All works fine, Pull stalk is Flash to pass with xenon but no high beam. Only low beam. Push the stalk is only low beam with dashboard indicator HighBeam (Blue icon) but no shutters. If I put 12v on the shutter wire they work fine, so the shutters are oke. What could be the problem here. Maybe somebody have a look at the TRC file and will find some wrong settings . Or is the FRM module that needs to be replaced: As far as i´m red in several forum posts it should be possible to get this working ok as oem with this FRM 2 Module. Or am I wrong? Please help, because I´m stuck in my options.
Attached files are read outs after coding. From FRM

FSW_PSW.MAN - newFRMnotWorkHighbeam.txt

F31B48 · 10-17-2021, 02:58 AM

I think you need to replace your nsw frm2 with a xe frm2 (xenon) An frm with nsw is only good for cars with halogen h/lights

I dealt with this issue when i put a nsw frm2 in my car with xenon h/lights. Had to install an xe frm2, then it worked fine. Just get a used one from a wrecked car.

wortel55 · 10-17-2021, 06:49 PM

Hi Eva bmw,

Well, I had this idea too. but it is strange that when i hooked up the xenons for the first time, they flickered. after coding cas and frm. and the oem wire change, the xenon does not flicker anymore. Önly the schuter is not working. Also, if you read here on forums, everybody is talking about only frm 2 modules who suppose to be working. But now i´m thinking, frm2 is not enough. Anyway I´ll try to get hold of a frm 2 or 3 XE or higher. Thanks for your support.

pmorg4 · 10-18-2021, 04:53 AM

EvaBmw is correct. You need the XE (AHL or Max Brose versions will also work) FRM2 or FRM3. The base version does not have the outputs to control the bi-xenon shutter.

wortel55 · 10-21-2021, 05:15 PM

Quote:

Originally Posted by pmorg4

EvaBmw is correct. You need the XE (AHL or Max Brose versions will also work) FRM2 or FRM3. The base version does not have the outputs to control the bi-xenon shutter.

Oky, then my suspicion is confirmed. Found one FRM 3 R XE. I'll let you know if it works fine once I installed and coded it.

10-15-2021, 04:08 PM	#1
wortel55 New Member 0 Rep 20 Posts Drives: BMW 318i LCI E91 Join Date: Aug 2021 Location: Netherlands iTrader: (0)	Shutter e91 does not work oem. Shutter e91 does not work oem Hello, i´m Bern from Holland and I drive a 381i LCI e91.2010. I replaced my halogens for LCI oem bi´xenon's. Made the oem wire change. Earth on pin 2 of the headlight connector and the shutter wire from pin 5 hl connector to pin 41 of my frm module the PL2 FRM II (LED,NSW) date 0609. Coded the CAS VO and FRM VO ( Add $522) and re-coded the FRM with the code data. I added the TRC code data in a attachment. All works fine, Pull stalk is Flash to pass with xenon but no high beam. Only low beam. Push the stalk is only low beam with dashboard indicator HighBeam (Blue icon) but no shutters. If I put 12v on the shutter wire they work fine, so the shutters are oke. What could be the problem here. Maybe somebody have a look at the TRC file and will find some wrong settings . Or is the FRM module that needs to be replaced: As far as i´m red in several forum posts it should be possible to get this working ok as oem with this FRM 2 Module. Or am I wrong? Please help, because I´m stuck in my options. Attached files are read outs after coding. From FRM FSW_PSW.MAN - newFRMnotWorkHighbeam.txt
	Appreciate 0 Tweet Quote

10-17-2021, 02:58 AM	#2
F31B48 Captain 293 Rep 654 Posts Drives: BMW G21 E61 LCI Join Date: Feb 2019 Location: Australia iTrader: (0)	I think you need to replace your nsw frm2 with a xe frm2 (xenon) An frm with nsw is only good for cars with halogen h/lights I dealt with this issue when i put a nsw frm2 in my car with xenon h/lights. Had to install an xe frm2, then it worked fine. Just get a used one from a wrecked car.
	Appreciate 0 Quote

10-17-2021, 06:49 PM	#3
wortel55 New Member 0 Rep 20 Posts Drives: BMW 318i LCI E91 Join Date: Aug 2021 Location: Netherlands iTrader: (0)	Hi Eva bmw, Well, I had this idea too. but it is strange that when i hooked up the xenons for the first time, they flickered. after coding cas and frm. and the oem wire change, the xenon does not flicker anymore. Önly the schuter is not working. Also, if you read here on forums, everybody is talking about only frm 2 modules who suppose to be working. But now i´m thinking, frm2 is not enough. Anyway I´ll try to get hold of a frm 2 or 3 XE or higher. Thanks for your support.
	Appreciate 0 Quote

10-18-2021, 04:53 AM	#4
pmorg4 Private 28 Rep 99 Posts Drives: BMW 335i Touring LCI Join Date: Nov 2020 Location: Surrey, UK iTrader: (0)	EvaBmw is correct. You need the XE (AHL or Max Brose versions will also work) FRM2 or FRM3. The base version does not have the outputs to control the bi-xenon shutter.
	Appreciate 0 Quote