RHD Single Turbo stock manifold

Brule · 04-17-2022, 03:23 AM

Made this.
T4 divided, precision 6466 mounted

Brule · 04-17-2022, 03:28 AM

Photos.

Brule · 04-17-2022, 09:31 PM

Photos

Brule · 04-19-2022, 01:34 AM

O2 sensors.

Socket · 04-19-2022, 06:31 AM

Some nice work there mate

Brule · 04-19-2022, 06:58 AM

Thanks.

rev210 · 04-20-2022, 02:48 AM

Way to recycle old shagged stock turbos dude. 👍
You could stick a pulsar turbo g35 1050 or g42 1200 onto this for a budget performer.
Assume you are getting the gate onto the housing again for this one?

Brule · 04-20-2022, 03:13 AM

Yea wastegate off the rear housing.

Brule · 04-20-2022, 03:21 AM

Yes you could put a pulsar turbo on it.
Thought about putting cheaper brands on it but struggle to see any turbo besides garrett or precision going on any of my kits.

jzx_andy · 04-20-2022, 04:25 AM

My man

Brule · 04-21-2022, 02:28 AM

Thanks

Heat sinks arrived and are now welded in.

Put new studs in manifold, 2 need to be cut to fit nuts.

Tried to fit 3 inch aluminium pipe but it need another silicone joiner at the top. Its ordered last week.

Wanted to make downpipe but realised I needed a precision flange off the turbo. You can see in one of the photos the v bands are not the same as other 3 inch v bands.

I have a few boxes of gear coming that will see this running.

Looking forward to making the down pipe. Downpipe has 87mm at the tightest point.

Brule · 04-21-2022, 02:32 AM

Photos didnt upload. I remember why I stopped using thid forum.

Brule · 05-03-2022, 05:38 PM

Done a few days work on this now.
Oik feed and drain made and fitted.
Wastegate welded to turbo.

Next up making the waterpipe off the block to water pump. It needs to be moved as it hits the manifold and will improve space for the downpipe.

Brule · 05-04-2022, 09:32 PM

90% done now.

Made the water pipe, exhaust and screamer.

Just have to remove everything and put gaskets on manifold and everything bsck on. (4-5 hours work) And have to make vaccuum lines which will take 10 minutes.

Photo of exhaust and screamer.
This is hoe I will dyno and roll race it but unable to go to drags like this.

Socket · 05-07-2022, 03:31 AM

Hats off to you mate.... pretty solid effort doing all this work solo..... wish I had your talent ... much respect

Brule · 05-07-2022, 04:49 AM

Thanks.

Torgus · 05-07-2022, 10:29 AM

Looks great!

Brule · 05-07-2022, 10:42 PM

Removed everything. Took 6 minutes.
Installed everything ready to start it. Took 3.5 hours.
Taking it to Dyno in 2 weeks.

Brule · 05-07-2022, 10:48 PM

Photos from today.

Brule · 05-07-2022, 10:50 PM

Attempt 2

Brule · 05-07-2022, 10:52 PM

F! Attempt 3

Brule · 05-08-2022, 02:10 AM

Its up and running.
Started first go like is daily driven.
First start in 5-6 months on e85.

Few revs.
Turbo sounds are nice.
Going to sound crazy at roll racing!

04-17-2022, 03:23 AM	#1
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	RHD Single Turbo stock manifold Made this. T4 divided, precision 6466 mounted
	Appreciate 1 eastsidaz212.00 Tweet Quote

04-17-2022, 03:28 AM	#2
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Photos. Attached Images
	Appreciate 2 shannon1676.50 Torgus3795.50 Quote

04-17-2022, 09:31 PM	#3
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Photos Attached Images
	Appreciate 3 shannon1676.50 eastsidaz212.00 jzx_andy243.50 Quote

04-19-2022, 01:34 AM	#4
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	O2 sensors. Attached Images
	Appreciate 2 shannon1676.50 M3 hacker70.50 Quote

04-19-2022, 06:31 AM	#5
Socket Lieutenant General 4682 Rep 11,956 Posts Drives: 335i Join Date: Nov 2014 Location: Australia iTrader: (4) Garage List 2008 BMW E92 [0.00]	Some nice work there mate
	Appreciate 1 Torgus3795.50 Quote

04-19-2022, 06:58 AM	#6
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Thanks.
	Appreciate 0 Quote

04-20-2022, 02:48 AM	#7
rev210 Private 49 Rep 88 Posts Drives: 335i 2008 Join Date: Oct 2018 Location: Perth iTrader: (0)	Way to recycle old shagged stock turbos dude. 👍 You could stick a pulsar turbo g35 1050 or g42 1200 onto this for a budget performer. Assume you are getting the gate onto the housing again for this one?
	Appreciate 0 Quote

04-20-2022, 03:13 AM	#8
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Yea wastegate off the rear housing.
	Appreciate 0 Quote

04-20-2022, 03:21 AM	#9
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Yes you could put a pulsar turbo on it. Thought about putting cheaper brands on it but struggle to see any turbo besides garrett or precision going on any of my kits.
	Appreciate 0 Quote

04-20-2022, 04:25 AM	#10
jzx_andy Slowpoke 244 Rep 291 Posts Drives: 2008 E92 335i N54 Join Date: Jul 2018 Location: Perth, Australia iTrader: (0)	My man __________________ build thread - OEM+ WIDEBODY \| Factory Individual Audio, Active Steering, Comfort Access & M-Sport optioned 6MT swapped \| Xtreme twin disk & SMF \| Advan RSII \| ST XTA \| F82 M4 heated front seats \| BMW Individual interior trims \| CIC/Combox retrofits \| Custom headlights \| 1M/M3 mirrors \| 335is auxiliary radiator \| LCI tails
	Appreciate 0 Quote

04-21-2022, 02:28 AM	#11
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Thanks Heat sinks arrived and are now welded in. Put new studs in manifold, 2 need to be cut to fit nuts. Tried to fit 3 inch aluminium pipe but it need another silicone joiner at the top. Its ordered last week. Wanted to make downpipe but realised I needed a precision flange off the turbo. You can see in one of the photos the v bands are not the same as other 3 inch v bands. I have a few boxes of gear coming that will see this running. Looking forward to making the down pipe. Downpipe has 87mm at the tightest point. Attached Images
	Appreciate 1 shannon1676.50 Quote

04-21-2022, 02:32 AM	#12
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Photos didnt upload. I remember why I stopped using thid forum. Attached Images
	Appreciate 1 shannon1676.50 Quote

05-03-2022, 05:38 PM	#13
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Done a few days work on this now. Oik feed and drain made and fitted. Wastegate welded to turbo. Next up making the waterpipe off the block to water pump. It needs to be moved as it hits the manifold and will improve space for the downpipe. Attached Images
	Appreciate 1 shannon1676.50 Quote

05-04-2022, 09:32 PM	#14
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	90% done now. Made the water pipe, exhaust and screamer. Just have to remove everything and put gaskets on manifold and everything bsck on. (4-5 hours work) And have to make vaccuum lines which will take 10 minutes. Photo of exhaust and screamer. This is hoe I will dyno and roll race it but unable to go to drags like this. Attached Images
	Appreciate 2 shannon1676.50 Socket4682.00 Quote

05-07-2022, 03:31 AM	#15
Socket Lieutenant General 4682 Rep 11,956 Posts Drives: 335i Join Date: Nov 2014 Location: Australia iTrader: (4) Garage List 2008 BMW E92 [0.00]	Hats off to you mate.... pretty solid effort doing all this work solo..... wish I had your talent ... much respect
	Appreciate 0 Quote

05-07-2022, 04:49 AM	#16
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Thanks.
	Appreciate 0 Quote

05-07-2022, 10:29 AM	#17
Torgus Slow. 3796 Rep 7,160 Posts Drives: N54 6466 100% E85 + Meth Join Date: Jun 2012 Location: Boston, MA iTrader: (2) Garage List 2007 BMW E92 [10.00] 2007 BMW E90 [0.00] 2006 BMW E91 [0.00]	Looks great! __________________ E92 6466 E85 + Meth/ E70 #1 fully deleted 2.8 race flash / E70 #2 JBD / E90 & E91 both tuned & retired Psalm 144
	Appreciate 0 Quote

05-07-2022, 10:42 PM	#18
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Removed everything. Took 6 minutes. Installed everything ready to start it. Took 3.5 hours. Taking it to Dyno in 2 weeks. Attached Images
	Appreciate 1 shannon1676.50 Quote

05-07-2022, 10:48 PM	#19
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Photos from today.
	Appreciate 0 Quote

05-07-2022, 10:50 PM	#20
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Attempt 2
	Appreciate 0 Quote

05-07-2022, 10:52 PM	#21
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	F! Attempt 3 Attached Images
	Appreciate 0 Quote

05-08-2022, 02:10 AM	#22
Brule Brigadier General 840 Rep 3,190 Posts Drives: 2007 335i e92 6spd man Join Date: Jul 2013 Location: Darwin iTrader: (0)	Its up and running. Started first go like is daily driven. First start in 5-6 months on e85. Few revs. Turbo sounds are nice. Going to sound crazy at roll racing!
	Appreciate 2 shannon1676.50 jzx_andy243.50 Quote