FS: Pre-LCI E90 OEM CF Mtech ('M Aerodynamic') rear diffuser trim piece (for non-335)

ssm12 · 07-26-2009, 01:14 PM

*** SOLD ***

*** $150.00 CAD - Local GTA pick up only ***

(Retails new for ~$1000 in GTA dealerships)

I am selling a used OEM (Part No. 51120404941) carbon fiber (CF) single-exhaust diffuser trim piece that fits onto the pre-LCI E90 Mtech (or 'M Aerodynamic') NON-335 rear bumper. The item was pre-installed on a used E90 Mtech rear that I acquired from another forum member back in June 2009. The previous owner had the diffuser for only a few months, and originally purchased it from Tischer. I am now re-selling the OEM CF diffuser because I recently swapped out the diffuser for a different CF one.

The OEM CF diffuser is in excellent condition, with only a few minor scratches that are barely visible upon close inspection (see red circle in pic below). Installation of the OEM CF diffuser is straight forward, and for reference I have posted a DIY that shows how I uninstalled it from my vehicle at http://www.e90post.com/forums/showthread.php?t=278959. The diffuser is secured in place by various tabs, 7 screws and 4 cotter pins (no extra adhesive tape or anything was used for the bumper that I got from the previous owner). For the install, you may either try to get a set of 4 new cotter pins yourself from Home Depot or something, or you can just re-use the original ones that I removed from my Mtech bumper. (I will include the old cotter pins with the diffuser shipment.) Note that since the item is an OEM part, there should be NO fitment issues with installing this diffuser on your pre-LCI E90 Mtech bumper.

Thanks for your interest!

Pic of the diffuser while it was still on my vehicle:

SGxi · 07-26-2009, 03:10 PM

How much are you looking for? Don't want to low ball... PM me...

Thanks!

NaTuReB0Y · 07-26-2009, 03:13 PM

can you cut the cf diffuser for quads?

ssm12 · 07-26-2009, 04:15 PM

Quote:

Originally Posted by SGxi

How much are you looking for? Don't want to low ball... PM me...

Thanks!

PM sent; thanks.

ssm12 · 07-26-2009, 04:23 PM

Quote:

Originally Posted by NaTuReB0Y

can you cut the cf diffuser for quads?

I've never seen any posts where someone has tried to cut the OEM CF single-exhaust diffuser to accommodate quads. When viewed from behind, the diffuser is definitely symmetrical except for the hole on the left hand side for the single exhaust, so I suppose that in theory one could just cut out a second hole on the right hand side and call it a day.

But if you've ever seen the MSRP on this thing, I don't think you'd want to take a chance and start cutting to find out later that the diffuser gets messed up in the process... (e.g. frayed edges, uneven cutting, etc.)

ssm12 · 08-01-2009, 11:46 AM

bump

ssm12 · 08-27-2009, 04:42 PM

bump

ssm12 · 10-17-2009, 01:44 AM

bump

mimiandi · 10-17-2009, 04:06 PM

I am pretty new at this. I have 323i as well. Do i need to replace the whole rear bumper to put on a diffuser?

ssm12 · 10-17-2009, 09:09 PM

Quote:

Originally Posted by mimiandi

I am pretty new at this. I have 323i as well. Do i need to replace the whole rear bumper to put on a diffuser?

In order to install this particular diffuser, you will need to replace your entire OEM e90 323i rear bumper with the M-tech (also known as 'M Aerodynamic' / 'M-sport') rear bumper. So the short answer is... "Yes."

ssm12 · 02-20-2010, 04:42 PM

bump

ssm12 · 03-31-2010, 09:30 PM

Asking price posted. Local GTA pick-up only, please.

DimSum · 03-31-2010, 11:29 PM

Great price, especially since it is dry carbon fiber!

mathu.bala · 04-01-2010, 01:16 AM

323i never comes with m-tech bumper

otherwise I would jump in.

SGxi · 04-01-2010, 09:05 AM

Bump for a good price!

ssm12 · 04-01-2010, 10:12 AM

Quote:

Originally Posted by DimSum

Great price, especially since it is dry carbon fiber!

Quote:

Originally Posted by SGxi

Bump for a good price!

Thanks!

homieG · 04-01-2010, 11:32 AM

wish i had an mtech bumper! lol

u selling ur blacklines?

ssm12 · 04-01-2010, 01:09 PM

Quote:

Originally Posted by homieG

wish i had an mtech bumper! lol

u selling ur blacklines?

No plans at the moment, sorry...

ssm12 · 04-18-2011, 11:32 PM

Almost forgot I still have this for sale... so BUMP

thebunkbedrocks · 05-23-2011, 08:36 PM

bump for the price

thebunkbedrocks · 05-23-2011, 08:37 PM

bump for the price .

RickG · 05-24-2011, 09:47 AM

grr soldd?... thats nice where did you get it?

07-26-2009, 01:14 PM	#1
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	FS: E90 OEM CF Mtech rear diffuser (for non-335) - Local GTA pickup only * SOLD * * $150.00 CAD - Local GTA pick up only * (Retails new for ~$1000 in GTA dealerships) I am selling a used OEM (Part No. 51120404941) carbon fiber (CF) single-exhaust diffuser trim piece that fits onto the pre-LCI E90 Mtech (or 'M Aerodynamic') NON-335 rear bumper. The item was pre-installed on a used E90 Mtech rear that I acquired from another forum member back in June 2009. The previous owner had the diffuser for only a few months, and originally purchased it from Tischer. I am now re-selling the OEM CF diffuser because I recently swapped out the diffuser for a different CF one. The OEM CF diffuser is in excellent condition, with only a few minor scratches that are barely visible upon close inspection (see red circle in pic below). Installation of the OEM CF diffuser is straight forward, and for reference I have posted a DIY that shows how I uninstalled it from my vehicle at http://www.e90post.com/forums/showthread.php?t=278959. The diffuser is secured in place by various tabs, 7 screws and 4 cotter pins (no extra adhesive tape or anything was used for the bumper that I got from the previous owner). For the install, you may either try to get a set of 4 new cotter pins yourself from Home Depot or something, or you can just re-use the original ones that I removed from my Mtech bumper. (I will include the old cotter pins with the diffuser shipment.) Note that since the item is an OEM part, there should be NO fitment issues with installing this diffuser on your pre-LCI E90 Mtech bumper. Thanks for your interest! Pic of the diffuser while it was still on my vehicle: Last edited by ssm12; 05-23-2011 at 11:43 PM..
	Appreciate 0 Tweet Quote

07-26-2009, 03:10 PM	#2
SGxi Major General 166 Rep 6,804 Posts Drives: E90 328xi Join Date: Oct 2006 Location: Toronto iTrader: (17) Garage List 2007 328xi [0.00]	How much are you looking for? Don't want to low ball... PM me... Thanks! __________________ MY07 A22 E90 N52Nxi
	Appreciate 0 Quote

07-26-2009, 03:13 PM	#3
NaTuReB0Y Powered By 36DD 370 Rep 7,369 Posts Drives: 2006 E90 Join Date: Jul 2005 Location: Inland Empire iTrader: (12)	can you cut the cf diffuser for quads? __________________ 2006 E90 330i Jet Black \| 20" WORK VS-XX \| FK452 \| H&R Sport on Koni Yellow \| REMUS QUAD
	Appreciate 0 Quote

08-01-2009, 11:46 AM	#6
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	bump
	Appreciate 0 Quote

08-27-2009, 04:42 PM	#7
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	bump
	Appreciate 0 Quote

10-17-2009, 01:44 AM	#8
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	bump
	Appreciate 0 Quote

10-17-2009, 04:06 PM	#9
mimiandi Private First Class 8 Rep 169 Posts Drives: 2009 323i Join Date: Sep 2009 Location: Vancouver iTrader: (0) Garage List 2009 323i [0.00]	I am pretty new at this. I have 323i as well. Do i need to replace the whole rear bumper to put on a diffuser?
	Appreciate 0 Quote

02-20-2010, 04:42 PM	#11
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	bump
	Appreciate 0 Quote

03-31-2010, 09:30 PM	#12
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	Asking price posted. Local GTA pick-up only, please.
	Appreciate 0 Quote

03-31-2010, 11:29 PM	#13
DimSum Banned 230 Rep 2,740 Posts Drives: SLOW Join Date: May 2008 Location: LITTLEBIMMER.COM iTrader: (10)	Great price, especially since it is dry carbon fiber!
	Appreciate 0 Quote

04-01-2010, 01:16 AM	#14
mathu.bala First Lieutenant 24 Rep 329 Posts Drives: 2009 323i/6mt Join Date: Aug 2009 Location: Kirkland, WA iTrader: (0) Garage List 2009 LCI 323i [0.00]	323i never comes with m-tech bumper otherwise I would jump in. __________________ 2009 323i Titanium Silver Metallic: Premium Pkg(Heated SW, Bluetooth, Sunroof), USB MFD Scoop,SWS-8,JL M6450
	Appreciate 0 Quote

04-01-2010, 09:05 AM	#15
SGxi Major General 166 Rep 6,804 Posts Drives: E90 328xi Join Date: Oct 2006 Location: Toronto iTrader: (17) Garage List 2007 328xi [0.00]	Bump for a good price! __________________ MY07 A22 E90 N52Nxi
	Appreciate 0 Quote

04-01-2010, 11:32 AM	#17
homieG Captain 29 Rep 884 Posts Drives: F Join Date: Sep 2009 Location: T.O. iTrader: (5)	wish i had an mtech bumper! lol u selling ur blacklines?
	Appreciate 0 Quote

04-18-2011, 11:32 PM	#19
ssm12 Private 53 Rep 87 Posts Drives: 2008 323i Join Date: Jul 2008 Location: Toronto, Canada iTrader: (7)	Almost forgot I still have this for sale... so BUMP
	Appreciate 0 Quote

05-23-2011, 08:36 PM	#20
thebunkbedrocks New Member 0 Rep 5 Posts Drives: black Join Date: May 2011 Location: Toronto iTrader: (0)	bump for the price
	Appreciate 0 Quote

05-23-2011, 08:37 PM	#21
thebunkbedrocks New Member 0 Rep 5 Posts Drives: black Join Date: May 2011 Location: Toronto iTrader: (0)	bump for the price .
	Appreciate 0 Quote

05-24-2011, 09:47 AM	#22
RickG Youngster 5 Rep 127 Posts Drives: f25 diesel Join Date: Apr 2011 Location: Ontario, Canada/ Portugal iTrader: (0)	grr soldd?... thats nice where did you get it?
	Appreciate 0 Quote