E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > JB+ Install Reviews and Tips



Reply
 
Thread Tools Search this Thread
      03-05-2010, 08:40 AM   #1
Mike@N54Tuning.com
Joint Chiefs of Staff
Canada
5044
Rep
116,174
Posts

Drives: 2007 335i, 2015 M3
Join Date: Dec 2008
Location: N54tuning.com

iTrader: (89)

JB+ Install Reviews and Tips

I closed the GB thread so I thought I would post the reviews and install tips from the participants here.

Quote:
Originally Posted by Kruz View Post
I installed mine last night. I swear once you figure out wtf it is you are unclipping it's a <3 min job. I sat there in my garage for 45 mins worried about breaking off the clip and if I was staring at the TMAP sensor.

Someone needs to get a close up shot of the TMAP sensor as the manual pics are not ideal.

A couple handy tips for installation....

If you wish to adjust the JB+ default setting, dont turn the blue dial. You need a small flathead to insert into the arrow groove and then dial in your setting. I cranked it up to 60-65% which is ~2:00 on the dial.

Use a penny duct taped to a string (so you dont drop .01) to slide into the clip for easiest removal. The USB cable idea doesnt seem to have enough width to slip the clip off.

It's hard to describe the motion and feel of pulling on the release clip, but leaning over the drivers side fender, reach in with your right arm and feel for the black corrugated plastic wire sleeve, and work your way upwards an inch or so up the three exposed wires, then comes the male housing, the clip and then the female housing.

Slide your penny up in the same order starting from the male housing...the clip is on top and at an angle to your right slightly. If you slide it up enough it should stay in place. Dont use the penny as a lever to pry the clip off; it should stay parallel to the housing.

It helps to step back and see if the penny is flush in the clip. If it is, go back in and pull the 3 wires down and away slightly. They will pop right out. Step back again with your penny and note the orientation of the now loose male housing.

Congrats. The hard part is done!

Grab your JB+ and plug in its male housing to the car's female housing you just released, it should lock in place. Then with one hand, feel and connect the car's male into your JB+'s female housing.

You are done!

Now for my first few runs....

My June Dynolicious baseline 0-60 runs were in the range of 5-5.6. No I am not a pro driver and have a 6MT. FWIW my car was dynod at that time at AMS at 276hp at the wheels.

I did three runs last night and the worst was 5.1....the best was 4.27 but it was mostly downwhill.
Pretty impressive so far.
Quote:
Originally Posted by bspaceman View Post
Installed mine the night I got it. At first I didnt think I would be able to do the work without removing the airbox, but after deciding there was no way I was gonna do all that at 12am, I pushed forward.

After attempting to lift the clip with everything from a small flathead to a little pick like tool, I used the USB cable. It definately took some patience but I got up and the harness out. As stated early, this is the hardest part of the whole installation.

After that, it was a breeze, just plug in the JB+ to the appropriate connections close the hood and you are done.

Before installing my JB+, I consulted a tech who suggested I run it at around 75%. I dialed the PSI to around 3 o'clock. I am currently still running those settings.

It was 12am when I took my car out for the test drive. To be honest, the immediate was subtle. It wasn't until the next day that I started to notice. Yesterday seemed even better. The car remains smooth, yet incredibly fast. I took my boss out for a drive and he noted that he believes the car is as fast as his porsche carerra. This is the only mod I currently have on my car. I will say, my car now seems to need a suspension upgrade

I can only imagine what the other JBs could do to this car but I dont think I should have possession of one of those
All I can say is thank you to Mike for a great group buy. Also, a big thanks to the peeps from my other post regarding my investigation into tuning and their recommendations.
Appreciate 0
      03-05-2010, 08:53 AM   #2
ianthegreat
Colonel
63
Rep
2,314
Posts

Drives: n54
Join Date: Apr 2008
Location: Pittsburgh/Houston

iTrader: (1)

Up early eh Mike?
Appreciate 0
      03-05-2010, 08:56 AM   #3
Mike@N54Tuning.com
Joint Chiefs of Staff
Canada
5044
Rep
116,174
Posts

Drives: 2007 335i, 2015 M3
Join Date: Dec 2008
Location: N54tuning.com

iTrader: (89)

Quote:
Originally Posted by ianthegreat View Post
Up early eh Mike?
Yuppers I find I am most productive in the morning and I like to have all the emails/PMs from the previous night answered and in peoples inboxes so when they logon or check their email in the morning they see their questions answered

Mike
Appreciate 0
      03-05-2010, 09:55 AM   #4
Scimitar335i
Major
213
Rep
1,313
Posts

Drives: 2007 335i
Join Date: Jun 2008
Location: Bay Area

iTrader: (12)

JB+ is a great tune for those who don't want to dig around in their ecus... one day though..eventually.. almost all graduate to the JB3 like I did!!!

Toward the end of my JB+ Career I had it at around 100% with no codes or anything.. and yes, it does respond well to higher octanes.. I stuck 1/2 a tank of Sunoco 100 octane in there once and it ripped!

Awesome tune!!!
__________________
2007 TiAg e90 335i sport. Yes, The e90 "Mustache" is cool!
Appreciate 0
      03-05-2010, 10:09 AM   #5
Kruz
Major
Kruz's Avatar
United_States
22
Rep
1,083
Posts

Drives: 2021 M2C 6MT
Join Date: Jun 2007
Location: Chicagoland

iTrader: (4)

Garage List
I intalled this Wed night at 60-65% and am ready to crank it up some more. Yeh I know it probably hasnt even adapted fully in <40 miles, but why not.

I plan to check for codes beforehand and do not expect any. I have a 7/07 production car and I believe I saw in the BT that my ECU was manuf just before that as well.

My 2 questions based on turning it up to 100%...
1. I run 93 octane all the time, so I should be okay right?
2. What is this solenoid bypass all about and is it necessary?
3. At >75%, and with a never updated ECU, I should theoretically not throw any tuner manip codes right?
__________________
2021 BMW M2 Competition, BSM, Exec Pkg, 6MT
GONE:07/07 E90 335xi SG
Black Dakota|Alum|ZSP|2AB|ZPP|ZCW|Nav|CA|6FL|PDC| Blacklines|3M
Summers: 235/40/18 265/35/18 Hankook Ventus V12 on VMR 701s
A/S: 225/40/18 255/35/18 Pirelli PZero Nero M+S on OEM 162s
Appreciate 0
      03-05-2010, 10:11 AM   #6
Scimitar335i
Major
213
Rep
1,313
Posts

Drives: 2007 335i
Join Date: Jun 2008
Location: Bay Area

iTrader: (12)

Quote:
Originally Posted by Kruz View Post
I intalled this Wed night at 60-65% and am ready to crank it up some more. Yeh I know it probably hasnt even adapted fully in <40 miles, but why not.

I plan to check for codes beforehand and do not expect any. I have a 7/07 production car and I believe I saw in the BT that my ECU was manuf just before that as well.

My 2 questions based on turning it up to 100%...
1. I run 93 octane all the time, so I should be okay right?
2. What is this solenoid bypass all about and is it necessary?
3. At >75%, and with a never updated ECU, I should theoretically not throw any tuner manip codes right?
1) Yup
2) Solenoid bypass is highly recommended for 100%, also gives that low end a little more kick!
3) above 75% you run the risk of throwing a tuner code... best get a BT Scanner if you plan on running it @ 100% from now on...
__________________
2007 TiAg e90 335i sport. Yes, The e90 "Mustache" is cool!
Appreciate 0
      03-05-2010, 10:47 AM   #7
Sal Collaziano
Lieutenant
Sal Collaziano's Avatar
United_States
60
Rep
424
Posts

Drives: 2015 BMW X5
Join Date: Jul 2008
Location: Royal Palm Beach, Florida

iTrader: (0)

Garage List
2007 335i  [0.00]
Quote:
Originally Posted by Mike@N54Tuning.com View Post
I closed the GB thread so I thought I would post the reviews and install tips from the participants here.
I think this is what Kruz wanted a better picture of...

http://www.e90post.com/forums/showpo...30&postcount=1
__________________
Sal Collaziano
Stinger Forum
Appreciate 0
      03-05-2010, 10:55 AM   #8
Mike@N54Tuning.com
Joint Chiefs of Staff
Canada
5044
Rep
116,174
Posts

Drives: 2007 335i, 2015 M3
Join Date: Dec 2008
Location: N54tuning.com

iTrader: (89)

Quote:
Originally Posted by Sal Collaziano View Post
I think this is what Kruz wanted a better picture of...

http://www.e90post.com/forums/showpo...30&postcount=1
Imbedded the pic..
Attached Images
 
Appreciate 0
      03-05-2010, 11:09 AM   #9
Sal Collaziano
Lieutenant
Sal Collaziano's Avatar
United_States
60
Rep
424
Posts

Drives: 2015 BMW X5
Join Date: Jul 2008
Location: Royal Palm Beach, Florida

iTrader: (0)

Garage List
2007 335i  [0.00]
Thank you. I took that picture with my iPhone and used Adobe Photoshop to brighten it up.
__________________
Sal Collaziano
Stinger Forum
Appreciate 0
      03-05-2010, 11:39 AM   #10
Kruz
Major
Kruz's Avatar
United_States
22
Rep
1,083
Posts

Drives: 2021 M2C 6MT
Join Date: Jun 2007
Location: Chicagoland

iTrader: (4)

Garage List
Nice job on the picture. With that angle, you must of just stuck your iphone down there and snapped huh?
__________________
2021 BMW M2 Competition, BSM, Exec Pkg, 6MT
GONE:07/07 E90 335xi SG
Black Dakota|Alum|ZSP|2AB|ZPP|ZCW|Nav|CA|6FL|PDC| Blacklines|3M
Summers: 235/40/18 265/35/18 Hankook Ventus V12 on VMR 701s
A/S: 225/40/18 255/35/18 Pirelli PZero Nero M+S on OEM 162s
Appreciate 0
      03-05-2010, 11:52 AM   #11
Sal Collaziano
Lieutenant
Sal Collaziano's Avatar
United_States
60
Rep
424
Posts

Drives: 2015 BMW X5
Join Date: Jul 2008
Location: Royal Palm Beach, Florida

iTrader: (0)

Garage List
2007 335i  [0.00]
Quote:
Originally Posted by Kruz View Post
Nice job on the picture. With that angle, you must of just stuck your iphone down there and snapped huh?
Thanks. And, yes. It definitely didn't work out that nicely on the first shot. Seeing the clip made it so much easier and I figured it would help for others as well.. It might not be a bad idea to use it in the actual documentation. All I want is $100,000,000.00 and I'll be happy..
__________________
Sal Collaziano
Stinger Forum
Appreciate 0
      03-05-2010, 04:39 PM   #12
frans335
Private
frans335's Avatar
United_States
4
Rep
51
Posts

Drives: 07 335i E92
Join Date: Jan 2010
Location: Leavenworth KS

iTrader: (0)

I just got mine and so far I have not been able to get it. I almost thought about taking the airbox out. That also looks like a pita. I tried for about 45 mins yesterday and gave up. I have very little mechanical ability .
__________________
07 335i E92 AW/Coral JB+

E46 M3
Dinan S2 Sold
Appreciate 0
      03-05-2010, 05:09 PM   #13
JayKay335i
Banned
Egypt
198
Rep
5,046
Posts

Drives: ///M323 DCT
Join Date: Apr 2009
Location: North Dakota; its best DUHHHHHH

iTrader: (1)

Quote:
Originally Posted by frans335 View Post
I just got mine and so far I have not been able to get it. I almost thought about taking the airbox out. That also looks like a pita. I tried for about 45 mins yesterday and gave up. I have very little mechanical ability .
Forget all the long install tips and all that. Locate the TMAP sensor. Jam a penny into the clip, tug. Thats it. Forget the penny, it will fall out eventually.
Appreciate 0
      03-05-2010, 05:29 PM   #14
Sal Collaziano
Lieutenant
Sal Collaziano's Avatar
United_States
60
Rep
424
Posts

Drives: 2015 BMW X5
Join Date: Jul 2008
Location: Royal Palm Beach, Florida

iTrader: (0)

Garage List
2007 335i  [0.00]
Quote:
Originally Posted by frans335 View Post
I just got mine and so far I have not been able to get it. I almost thought about taking the airbox out. That also looks like a pita. I tried for about 45 mins yesterday and gave up. I have very little mechanical ability .
Seriously, it's a lot easier than you're thinking. Take JayKay's advice.. I'm lucky I can fill my tank with gas and I installed it myself. The first time took me about 45 minutes because I didn't know what to look for and couldn't see anything. Once I got that picture up above, I could feel around and know what the sensor looked like by feeling it. Now I can install and uninstall the piece in a few minutes.
__________________
Sal Collaziano
Stinger Forum
Appreciate 0
      03-05-2010, 05:58 PM   #15
frans335
Private
frans335's Avatar
United_States
4
Rep
51
Posts

Drives: 07 335i E92
Join Date: Jan 2010
Location: Leavenworth KS

iTrader: (0)

Thanks guys, I will try again.
__________________
07 335i E92 AW/Coral JB+

E46 M3
Dinan S2 Sold
Appreciate 0
      03-05-2010, 06:28 PM   #16
ianthegreat
Colonel
63
Rep
2,314
Posts

Drives: n54
Join Date: Apr 2008
Location: Pittsburgh/Houston

iTrader: (1)

Quote:
Originally Posted by frans335 View Post
I just got mine and so far I have not been able to get it. I almost thought about taking the airbox out. That also looks like a pita. I tried for about 45 mins yesterday and gave up. I have very little mechanical ability .
The airbox is cake and would make this install so much easier. The only hard thing about the air box are the 3 little rubber wire holders on the back right that you need to slide off.
Appreciate 0
      03-05-2010, 07:47 PM   #17
Htown09
Captain
Htown09's Avatar
46
Rep
783
Posts

Drives: E92
Join Date: Oct 2009
Location: Earth

iTrader: (3)

Quote:
Originally Posted by ianthegreat View Post
The airbox is cake and would make this install so much easier. The only hard thing about the air box are the 3 little rubber wire holders on the back right that you need to slide off.
+1 if it takes you longer than 20-30 minutes to locate the clip then take the airbox off and it will stare you right in the face.
Appreciate 0
      03-06-2010, 11:05 PM   #18
bspaceman
The Last Beautiful Free Soul On This Planet
bspaceman's Avatar
United_States
15
Rep
627
Posts

Drives: Jet Black 335i coupe
Join Date: Aug 2007
Location: Cedar Park, TX

iTrader: (2)

I will add that my car continues to morph into a bit of beast. It seems to almost snarl, but in the best way! I actually slid a bit on the onramp I drive everyday So in addition to my previous advice I should add to be careful out there and remember to adjust your driving as well.

Unfortunetly, I have come down with the bug. It started with the JB+ and is now progressing to an AFE DCI. Prognosis looks bad indeed....
__________________

Jet Black/Black Leather 335i coupe (totaled courtesy of the pizza kid
Sport/Premi/Comft/Nav - iDrive/Sirius/iPod/OEM Body kit, M Sideskirts, M deck lip, Miro 366s on Nitto 555 NTs, Matte Black Grills, Valentine 1 hardwire, 35% tint, BMS Lighting, BMS computer magic, BMS Dual Cone
Appreciate 0
      03-06-2010, 11:33 PM   #19
Mike@N54Tuning.com
Joint Chiefs of Staff
Canada
5044
Rep
116,174
Posts

Drives: 2007 335i, 2015 M3
Join Date: Dec 2008
Location: N54tuning.com

iTrader: (89)

Quote:
Originally Posted by bspaceman View Post
I will add that my car continues to morph into a bit of beast. It seems to almost snarl, but in the best way! I actually slid a bit on the onramp I drive everyday So in addition to my previous advice I should add to be careful out there and remember to adjust your driving as well.

Unfortunetly, I have come down with the bug. It started with the JB+ and is now progressing to an AFE DCI. Prognosis looks bad indeed....
I see a JB3 on the horizon.. LOL

Mike
Appreciate 0
      03-07-2010, 08:49 AM   #20
bmwstyle
New Member
2
Rep
27
Posts

Drives: E92 BugKilla
Join Date: Sep 2009
Location: Houston, TX

iTrader: (0)

Here's an idea. Anybody have a way to post up a video of the exact location of the TMAP? I have an idea of where it is and I could get my point and shoot but I don't have a way to post it. hehehe
Appreciate 0
      03-07-2010, 01:33 PM   #21
Kid Eh
I used to be conceited, now I'm perfect.
Kid Eh's Avatar
Canada
610
Rep
1,838
Posts

Drives: 2018 M3 CS
Join Date: Sep 2006
Location: Toronto

iTrader: (1)

Garage List
2018 BMW M3 CS  [0.00]
Quote:
Originally Posted by bmwstyle View Post
Here's an idea. Anybody have a way to post up a video of the exact location of the TMAP? I have an idea of where it is and I could get my point and shoot but I don't have a way to post it. hehehe
+1

I'm waiting until I know exactly what I'm doing before I install. Also waiting for a BT tool.
__________________
2018 M3 CS - Alpine White l l

"I used to be conceited. Now I'm perfect"
Appreciate 0
      03-07-2010, 01:58 PM   #22
iBoost
Retired e90post Member
iBoost's Avatar
135
Rep
3,038
Posts

Drives: real slow
Join Date: Nov 2009
Location: Las Vegas

iTrader: (13)

Quote:
Originally Posted by bmwstyle View Post
Here's an idea. Anybody have a way to post up a video of the exact location of the TMAP? I have an idea of where it is and I could get my point and shoot but I don't have a way to post it. hehehe

its simple to do on youtube.
Appreciate 0
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:08 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST