Hmmm...whats this?

cn555ic · 04-30-2010, 03:56 PM

scottp999 · 04-30-2010, 04:00 PM

You have been a busy bee.

scalbert · 04-30-2010, 04:01 PM

Wet, where did you tap for the fuel supply?

tek818 · 04-30-2010, 04:02 PM

pretty gnarly setup you got there... congrats!

cn555ic · 04-30-2010, 04:12 PM

Scalbert. It's going to be a dry shot. Using the same setup as Shiv. Just doing a little bit of the hardware for now! Still a long way to go before it's functionable. Have to wait till Shiv finally finishes the nitrous setup with Procede

GeorgiaTech335coupe · 04-30-2010, 04:12 PM

A baby bottle?

scalbert · 04-30-2010, 04:13 PM

Quote:

Originally Posted by cn555ic

Scalbert. It's going to be a dry shot. Using the same setup as Shiv. Just doing a little bit of the hardware for now! Still a long way to go before it's functionable. Have to wait till Shiv finally finishes the nitrous setup with Procede

Gotcha, the red line to a solenoid is what got my attention.

cn555ic · 04-30-2010, 04:14 PM

Quote:

Originally Posted by GeorgiaTech335coupe

A baby bottle?

cstmx_ryder · 04-30-2010, 04:21 PM

OP,

So are you running meth and nos, or is it just nos?

Also, what is the HP yield by using meth vs nos?

Wasn't there a thread a while back stating that methanol is bad for aluminum blocks as they eat up the aluminum material? Or is this a myth?

cn555ic · 04-30-2010, 04:42 PM

Quote:

Originally Posted by scalbert

Gotcha, the red line to a solenoid is what got my attention.

The red line is not connected to the NX solenoid, its appears to be from the first pic, but actually its hooked up to the meth solenoid! Look at this pic!

UAP1 · 04-30-2010, 04:54 PM

Looking good!

cn555ic · 04-30-2010, 11:48 PM

Shiv I am ready for you soon to show me the promise land with Nitrous setup to Procede!!

cn555ic · 05-02-2010, 11:09 PM

My little 5lb bottle! Didn't want to go overboard and get the gigantic 10lb bottle, plus convertible trunk space is limited..

Former_Boosted_IS · 05-03-2010, 05:59 AM

Good looking NX stuff! You will love it!

cn555ic · 05-03-2010, 07:38 AM

Quote:

Originally Posted by Former_Boosted_IS

Good looking NX stuff! You will love it!

Yes you are definitely right about that...very impressive indeed...I will refer to your DIY for sure like I did with meth....

cn555ic · 05-03-2010, 07:41 AM

Hey FBIS I have a question...the fitting to the inlet of the solenoid, is that where the fitting with the filter screen gets attached to?

Former_Boosted_IS · 05-03-2010, 07:46 AM

I do believe the filter goes on the inlet side. I think the instruction manual specifies the location.

cn555ic · 05-03-2010, 07:47 AM

Quote:

Originally Posted by Former_Boosted_IS

I do believe the filter goes on the inlet side. I think the instruction manual specifies the location.

I didn't get any instructions whatsover with my kit!!

Not one page of anything!

I have been looking at NX express website under their instruction section but there is no instructions that are specific to the basic kit that I bought...but it looks as though the only thing that I wont be using is the WOT switch, Procede will control the functionality of the nitrous trigger.

cn555ic · 05-04-2010, 07:53 AM

FBIS...what is this piece thats on the nitrous bottle neck thats covered in a green cap used for? The little plastic cover on mine is cracked in half, it came like that shipped...Wanted to know if that cap is necessarry...

Former_Boosted_IS · 05-04-2010, 08:07 AM

Quote:

Originally Posted by cn555ic

I didn't get any instructions whatsover with my kit!!

Not one page of anything!

I have been looking at NX express website under their instruction section but there is no instructions that are specific to the basic kit that I bought...but it looks as though the only thing that I wont be using is the WOT switch, Procede will control the functionality of the nitrous trigger.

Ok, I looked it up online. The filter does go on the inlet side of the solenoid!

Funkmob · 05-04-2010, 08:09 AM

I dunno , but isn't that just the cover cap of the nitrous line connection

cn555ic · 05-04-2010, 08:11 AM

Quote:

Originally Posted by Former_Boosted_IS

Ok, I looked it up online. The filter does go on the inlet side of the solenoid!

THanks Bro...what about that green cap...whats that for in terms of the neck used for...my green cap/lid came cracked, but it doesn't seem like it has any useful function maybe just to protect the head behind it! What do you think?:

04-30-2010, 03:56 PM	#1
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Hmmm...whats this? Attached Images Last edited by cn555ic; 10-04-2010 at 11:38 PM..
	Appreciate 0 Tweet Quote

04-30-2010, 04:00 PM	#2
scottp999 Brigadier General 136 Rep 4,764 Posts Drives: 4runner SR5 Join Date: Mar 2007 Location: MD iTrader: (2) Garage List 2007 BMW 335 [9.00]	You have been a busy bee.
	Appreciate 0 Quote

04-30-2010, 04:01 PM	#3
scalbert Major General 158 Rep 5,776 Posts Drives: '13 S4, '15 Q7 Join Date: Feb 2007 Location: Woodstock, GA iTrader: (8)	Wet, where did you tap for the fuel supply?
	Appreciate 0 Quote

04-30-2010, 04:02 PM	#4
tek818 Lieutenant Colonel 140 Rep 1,953 Posts Drives: 2020 X3M Competition Join Date: Mar 2007 Location: Los Angeles, CA iTrader: (2) Garage List 2018 M3 ZCP [9.50]	pretty gnarly setup you got there... congrats!
	Appreciate 0 Quote

04-30-2010, 04:12 PM	#5
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Scalbert. It's going to be a dry shot. Using the same setup as Shiv. Just doing a little bit of the hardware for now! Still a long way to go before it's functionable. Have to wait till Shiv finally finishes the nitrous setup with Procede
	Appreciate 0 Quote

04-30-2010, 04:12 PM	#6
GeorgiaTech335coupe Lieutenant Colonel 81 Rep 1,883 Posts Drives: Black BMW 335i coupe Join Date: Mar 2007 Location: USA iTrader: (0)	A baby bottle? __________________ Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(e90post.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
	Appreciate 0 Quote

04-30-2010, 04:21 PM	#9
cstmx_ryder Colonel 173 Rep 2,875 Posts Drives: A metal box with a roundel Join Date: Jul 2007 Location: Portland, OR iTrader: (2)	OP, So are you running meth and nos, or is it just nos? Also, what is the HP yield by using meth vs nos? Wasn't there a thread a while back stating that methanol is bad for aluminum blocks as they eat up the aluminum material? Or is this a myth? __________________ '08 AW E90 335i PROcede V5 \| BMS DCI \| RR DPs \| ETS FMIC \| FORGE DVs \| Stett CP \| Vanguard \| PSS10
	Appreciate 0 Quote

04-30-2010, 04:54 PM	#11
UAP1 www.UltimateAutoPortal.co m 63 Rep 556 Posts Drives: 2007 BMW 335i. Few mods. Join Date: Mar 2010 Location: Texas iTrader: (3)	Looking good! __________________ http://www.ultimateautoportal.com/uap/learn-more
	Appreciate 0 Quote

04-30-2010, 11:48 PM	#12
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Shiv I am ready for you soon to show me the promise land with Nitrous setup to Procede!!
	Appreciate 0 Quote

05-02-2010, 11:09 PM	#13
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	My little 5lb bottle! Didn't want to go overboard and get the gigantic 10lb bottle, plus convertible trunk space is limited.. Attached Images
	Appreciate 0 Quote

05-03-2010, 05:59 AM	#14
Former_Boosted_IS Major General 315 Rep 5,175 Posts Drives: 4 Wheels Join Date: Aug 2007 Location: Planet Earth! iTrader: (15)	Good looking NX stuff! You will love it!
	Appreciate 0 Quote

05-03-2010, 07:41 AM	#16
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Hey FBIS I have a question...the fitting to the inlet of the solenoid, is that where the fitting with the filter screen gets attached to? Attached Images
	Appreciate 0 Quote

05-03-2010, 07:46 AM	#17
Former_Boosted_IS Major General 315 Rep 5,175 Posts Drives: 4 Wheels Join Date: Aug 2007 Location: Planet Earth! iTrader: (15)	I do believe the filter goes on the inlet side. I think the instruction manual specifies the location.
	Appreciate 0 Quote

05-04-2010, 07:53 AM	#19
cn555ic 464 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	FBIS...what is this piece thats on the nitrous bottle neck thats covered in a green cap used for? The little plastic cover on mine is cracked in half, it came like that shipped...Wanted to know if that cap is necessarry... Attached Images
	Appreciate 0 Quote

05-04-2010, 08:09 AM	#21
Funkmob First Lieutenant 22 Rep 306 Posts Drives: 335i E92 space grey Join Date: Oct 2009 Location: Belgium iTrader: (0)	I dunno , but isn't that just the cover cap of the nitrous line connection __________________ 335I AT 2007. Vishnu V5 / UR CAI / HPF Intercooler / ER Charge pipe / Synapse BOV / Macht Shnell dp's / Vanguard catless exhaust / BSH occ / Labonte S4 Meth injection / Quiafe LSD / Full M3 suspension parts / Bilstein PSS10 / EBC brakes and lines / RB turbo's
	Appreciate 0 Quote