ECU sub-connector problem

tufgsd · 07-11-2010, 02:43 PM

Ok, I think I really screwed up now. I was removing the JB3, the removal process was going very smooth. So, I take out the large connector and the slider comes all the way out. No biggie I though, i just set it aside. After plugging all the factor stuff back together, I put the connectors back on, except I forgot to put the slider back on the large connector. So, now not only does my car not start, the big connector will not come off, for me to add the slider back in. I know the reason is the conector is not all the way in for the car to start.

Anyone have any advice or thread that they can point me too?

alextremo · 07-11-2010, 02:53 PM

Similar thing happened to me - I was able to get my fingertips underneath the connector and use them for leverage to pry up the connector evenly on all sides. Hope this helps.

ren · 07-11-2010, 05:38 PM

pulling the ecu out of its tray should make it easier. Just pry the two tabs holding it in the slot.

David 12 · 07-11-2010, 10:38 PM

During the install you pressed on a tab on the ecu subconnector to take the slider out.

Press on the same area on the subconnector (it is on the top) with your small screwdriver and it will lift out easily.

Then attach the slider and press the slider in as you lower the subconnector, they reattach as a unit.

Dave

Former car: 2007 335i JB3

tufgsd · 08-03-2010, 05:10 PM

well the issue finally got fixed for $2K and 3 weeks later that BMW charged me. I did not tell them what I did, but they claimed that the ECM became corrupt. Not sure how, but I was not going to question it. I need to find a local mechanic that knows how to work on 335i in Little Rock. BMW is killing me on prices.

ren · 08-03-2010, 05:34 PM

what did they replace for 2K? do you have a list of parts on the service invoice?

cn555ic · 08-03-2010, 05:38 PM

Quote:

Originally Posted by tufgsd

well the issue finally got fixed for $2K and 3 weeks later that BMW charged me. I did not tell them what I did, but they claimed that the ECM became corrupt. Not sure how, but I was not going to question it. I need to find a local mechanic that knows how to work on 335i in Little Rock. BMW is killing me on prices.

Wow...they robbed you blind...Make sure you see the invoice and ask them for the parts back if thats the case which I doubt...You car didn't start was because the connectors were not seated right...All they did was take the subconnector out replace the slider and connected it back, but only thing that went wrong was that they made 2000 dollars for themselves..

joec500 · 08-03-2010, 05:42 PM

My guess is they replaced his DME which is 1500+ Labor....2k seems about right.

alextremo · 08-03-2010, 05:56 PM

you really couldn't get the connector off? Or did you fix that and still couldn't get the car started with it attached properly?

tufgsd · 08-03-2010, 06:32 PM

Quote:

Originally Posted by erensf

what did they replace for 2K? do you have a list of parts on the service invoice?

Here is what the invoice says:
Installed 12 14 7 611 358: RMFD Basic Control Unit --$1368.11
Installed 51 71 7 237 195: Support Lifting Platform -- 4@27.79 -- $111.16
Labor $524.75

Now here is the question: Do I get an extended warranty on the DME since they installed a new o

I would have rather gone to a local mechanic that knew how to work on these cars instead of dealer, but I am yet to find anyone in Little Rock, AR.

tufgsd · 08-03-2010, 06:34 PM

Quote:

Originally Posted by alextremo

you really couldn't get the connector off? Or did you fix that and still couldn't get the car started with it attached properly?

I really could not get the connectors off. Tried all suggestions from Forum members. Plus had an angry wife breathing down my neck..........

ren · 08-03-2010, 06:46 PM

Quote:

Originally Posted by tufgsd

Plus had an angry wife breathing down my neck..........

Now it makes sense that you paid $2K to get it fixed.

ren · 08-03-2010, 06:56 PM

Quote:

Originally Posted by tufgsd

Now here is the question: Do I get an extended warranty on the DME since they installed a new o

I would have rather gone to a local mechanic that knew how to work on these cars instead of dealer, but I am yet to find anyone in Little Rock, AR.

You should get a 2 year unlimited mileage warranty on the DME.

A local mechanic wouldn't be able to replace your DME, I don't think it's plug&play. But a handy JB3/Procede user would have a chance at taking the connector out.

bolty · 08-03-2010, 09:19 PM

Quote:

Originally Posted by erensf

Now it makes sense that you paid $2K to get it fixed.

He took a 2 thousand dollar punch, square on the chin. Poor guy.

I wonder if the ecu was really corrupted or just an excuse to give him a new one.

FlyingHorse · 08-03-2010, 10:54 PM

Quote:

Originally Posted by tufgsd

I really could not get the connectors off. Tried all suggestions from Forum members. Plus had an angry wife breathing down my neck..........

Maybe try post for help in your regional forum and see anyone can help you locally.

07-11-2010, 02:43 PM	#1
tufgsd Private 7 Rep 61 Posts Drives: 2007 BMW 335i Sedan Join Date: Dec 2009 Location: Arkansas iTrader: (0) Garage List 2007 335i Sedan [0.00]	ECU sub-connector problem - will not come off Ok, I think I really screwed up now. I was removing the JB3, the removal process was going very smooth. So, I take out the large connector and the slider comes all the way out. No biggie I though, i just set it aside. After plugging all the factor stuff back together, I put the connectors back on, except I forgot to put the slider back on the large connector. So, now not only does my car not start, the big connector will not come off, for me to add the slider back in. I know the reason is the conector is not all the way in for the car to start. Anyone have any advice or thread that they can point me too? __________________ 2007 BMW 335i Sedan - Titanium Silver - BMS DUal Cone Intake - JB4 PnP Map 7 - ETS Intercooler = BSH Competition Oil Catch Can - STETT CP w/ DV - Macht Schnell 3" Stainless Catless Track Downpipes - BMS Downpipe Fix v3 - V1 Hardwired - SWS Subs w/Alpine Amp //Coming Soon: Borla Aggressive Cat Back Exhaust - - FULL VC-2 Meth Injec Kit - AR Design Stage 1 Oil Cooler
	Appreciate 0 Tweet Quote

07-11-2010, 02:53 PM	#2
alextremo Captain 51 Rep 966 Posts Drives: F10 550i Join Date: Sep 2008 Location: USA iTrader: (5)	Similar thing happened to me - I was able to get my fingertips underneath the connector and use them for leverage to pry up the connector evenly on all sides. Hope this helps.
	Appreciate 0 Quote

07-11-2010, 05:38 PM	#3
ren Captain 62 Rep 840 Posts Drives: 2024 X7 M60i Join Date: Jan 2007 Location: U.S. iTrader: (8)	pulling the ecu out of its tray should make it easier. Just pry the two tabs holding it in the slot.
	Appreciate 0 Quote

07-11-2010, 10:38 PM	#4
David 12 Major 115 Rep 1,048 Posts Drives: 2019 BMW X5 50i BSM, M Sport Join Date: Jan 2007 Location: Omaha iTrader: (0)	During the install you pressed on a tab on the ecu subconnector to take the slider out. Press on the same area on the subconnector (it is on the top) with your small screwdriver and it will lift out easily. Then attach the slider and press the slider in as you lower the subconnector, they reattach as a unit. Dave Former car: 2007 335i JB3
	Appreciate 0 Quote

08-03-2010, 05:10 PM	#5
tufgsd Private 7 Rep 61 Posts Drives: 2007 BMW 335i Sedan Join Date: Dec 2009 Location: Arkansas iTrader: (0) Garage List 2007 335i Sedan [0.00]	well the issue finally got fixed for $2K and 3 weeks later that BMW charged me. I did not tell them what I did, but they claimed that the ECM became corrupt. Not sure how, but I was not going to question it. I need to find a local mechanic that knows how to work on 335i in Little Rock. BMW is killing me on prices. __________________ 2007 BMW 335i Sedan - Titanium Silver - BMS DUal Cone Intake - JB4 PnP Map 7 - ETS Intercooler = BSH Competition Oil Catch Can - STETT CP w/ DV - Macht Schnell 3" Stainless Catless Track Downpipes - BMS Downpipe Fix v3 - V1 Hardwired - SWS Subs w/Alpine Amp //Coming Soon: Borla Aggressive Cat Back Exhaust - - FULL VC-2 Meth Injec Kit - AR Design Stage 1 Oil Cooler
	Appreciate 0 Quote

08-03-2010, 05:34 PM	#6
ren Captain 62 Rep 840 Posts Drives: 2024 X7 M60i Join Date: Jan 2007 Location: U.S. iTrader: (8)	what did they replace for 2K? do you have a list of parts on the service invoice?
	Appreciate 0 Quote

08-03-2010, 05:42 PM	#8
joec500 Brigadier General 133 Rep 3,049 Posts Drives: it has 4 wheels Join Date: Jul 2008 Location: Los Angeles iTrader: (11)	My guess is they replaced his DME which is 1500+ Labor....2k seems about right.
	Appreciate 0 Quote

08-03-2010, 05:56 PM	#9
alextremo Captain 51 Rep 966 Posts Drives: F10 550i Join Date: Sep 2008 Location: USA iTrader: (5)	you really couldn't get the connector off? Or did you fix that and still couldn't get the car started with it attached properly?
	Appreciate 0 Quote