FS: New Beru TPMS Sensors + Valve Stems and Multi-Piece TPMS Adapters

coolchu001 · 08-08-2010, 06:16 PM

BIMMERPOST / Classifieds

Asking Price:

None

Item Interest

I have a new set of Beru TPMS adapters for BMW 3 series from 06-09. They are brand new and were not installed since my tires installer was not able to mount the tires over them due to the design of my new wheels. They come with a set of new valve stems as well. These were purchased for my 09 335d from TireRack.com.

Asking for SOLD.

I also have a set of TPMS adapters for multi-piece wheels. They are forged by Marcato. These are needed if the valve stem hole is positions in the center of the wheels. Missing 1 of the rubber seaters.

Asking for $35 shipped.

Will accept cash, postal money order, or paypal (non-CC)

EYE4SPEED · 08-09-2010, 05:45 AM

If these are for your ITC wheels - the installer needs to drill a hole in each wheel and install the OE sensors in the recess of the wheel to allow for clearance during installation. Then you can use the 90 degree valves for filling the air only.

I have the same wheels and just went through it. This applies to pre-TPMS wheels as well. The other option, as advised to me from another member on here with the same wheels, was to use the iForged TPMS adapaters.

The Marcato eBay valve stems are not the right adapters for the ITC application.

coolchu001 · 08-10-2010, 10:20 PM

Quote:

Originally Posted by EYE4SPEED

If these are for your ITC wheels - the installer needs to drill a whole in each wheel and install the OE sensors in the recess of the wheel to allow for clearance during installation. Then you can use the 90 degree valves for filling the air only.

I have the same wheels and just went through it. This applies to pre-TPMS wheels as well. The other option, as advised to me from another member on here with the same wheels, was to use the iForged TPMS adapaters.

The Marcato eBay valve stems are not the right adapters for the ITC application.

Thanks for the advice. I already mounted the tires and left it without the sensors. I may add them next time I need to get all new tires...

coolchu001 · 08-30-2010, 08:50 PM

bump, the tpms adapters are still available

coolchu001 · 12-17-2010, 03:34 PM

TPMS adapter still available

coolchu001 · 02-28-2011, 11:38 AM

TPMS adapters still available

mrj25 · 02-28-2011, 12:49 PM

Would the TPMS fit on a 2011 e90? I just picked up a new set of 19" VMR VB3 in gunmetal.

EYE4SPEED · 02-28-2011, 12:52 PM

Late model 2009 LCI's require 433hz (though these are 433?). If they are compatible with older vehicles, they will not work with your car (I think they're sold anyway).

coolchu001 · 07-07-2011, 04:52 PM

bump, tpms adapters still available

08-08-2010, 06:16 PM	#1
coolchu001 Lieutenant 49 Rep 583 Posts Drives: 09 BMW 335d Join Date: Aug 2009 Location: OH iTrader: (30)	FS: New Beru TPMS Sensors + Valve Stems and Multi-Piece TPMS Adapters BIMMERPOST / Classifieds Asking Price: None Item Interest I have a new set of Beru TPMS adapters for BMW 3 series from 06-09. They are brand new and were not installed since my tires installer was not able to mount the tires over them due to the design of my new wheels. They come with a set of new valve stems as well. These were purchased for my 09 335d from TireRack.com. Asking for SOLD. I also have a set of TPMS adapters for multi-piece wheels. They are forged by Marcato. These are needed if the valve stem hole is positions in the center of the wheels. Missing 1 of the rubber seaters. Asking for $35 shipped. Will accept cash, postal money order, or paypal (non-CC) Last edited by coolchu001; 12-17-2010 at 03:34 PM..
	Appreciate 0 Tweet Quote

08-09-2010, 05:45 AM	#2
EYE4SPEED Ex-Diesel Driver 65 Rep 2,000 Posts Drives: Audi SQ5 Join Date: Apr 2010 Location: West Coast... of Michigan iTrader: (22)	If these are for your ITC wheels - the installer needs to drill a hole in each wheel and install the OE sensors in the recess of the wheel to allow for clearance during installation. Then you can use the 90 degree valves for filling the air only. I have the same wheels and just went through it. This applies to pre-TPMS wheels as well. The other option, as advised to me from another member on here with the same wheels, was to use the iForged TPMS adapaters. The Marcato eBay valve stems are not the right adapters for the ITC application. __________________ FS: HRE Center Caps http://www.e90post.com/forums/showth...post13972317l] Last edited by EYE4SPEED; 08-11-2010 at 04:13 PM..
	Appreciate 0 Quote

08-30-2010, 08:50 PM	#4
coolchu001 Lieutenant 49 Rep 583 Posts Drives: 09 BMW 335d Join Date: Aug 2009 Location: OH iTrader: (30)	bump, the tpms adapters are still available __________________
	Appreciate 0 Quote

12-17-2010, 03:34 PM	#5
coolchu001 Lieutenant 49 Rep 583 Posts Drives: 09 BMW 335d Join Date: Aug 2009 Location: OH iTrader: (30)	TPMS adapter still available __________________
	Appreciate 0 Quote

02-28-2011, 11:38 AM	#6
coolchu001 Lieutenant 49 Rep 583 Posts Drives: 09 BMW 335d Join Date: Aug 2009 Location: OH iTrader: (30)	TPMS adapters still available __________________
	Appreciate 0 Quote

02-28-2011, 12:49 PM	#7
mrj25 Colonel 201 Rep 2,163 Posts Drives: 2011 335i E90 LCI Join Date: Dec 2010 Location: OC-LA, CALI iTrader: (21)	Would the TPMS fit on a 2011 e90? I just picked up a new set of 19" VMR VB3 in gunmetal.
	Appreciate 0 Quote

02-28-2011, 12:52 PM	#8
EYE4SPEED Ex-Diesel Driver 65 Rep 2,000 Posts Drives: Audi SQ5 Join Date: Apr 2010 Location: West Coast... of Michigan iTrader: (22)	Late model 2009 LCI's require 433hz (though these are 433?). If they are compatible with older vehicles, they will not work with your car (I think they're sold anyway). __________________ FS: HRE Center Caps http://www.e90post.com/forums/showth...post13972317l] Last edited by EYE4SPEED; 02-28-2011 at 06:24 PM..
	Appreciate 0 Quote

07-07-2011, 04:52 PM	#9
coolchu001 Lieutenant 49 Rep 583 Posts Drives: 09 BMW 335d Join Date: Aug 2009 Location: OH iTrader: (30)	bump, tpms adapters still available __________________
	Appreciate 0 Quote