Procede canclear question

Noelpolar · 06-02-2011, 08:24 AM

Will the can clear functionality on the Procede (v5) clear the codes thrown up by catless DPs on a Jan 2008 production e92 on original dme software?

I've searched and know 2007 production it pro ally won't.

Just installed DPs and got a couple of half engine lights within the first 50 miles and then the full engine light has come on. Have can clear on (default)

C4sF80M3 · 06-02-2011, 08:35 AM

Quote:

Originally Posted by Noelpolar

Will the can clear functionality on the Procede (v5) clear the codes thrown up by catless DPs on a Jan 2008 production e92 on original dme software?

I've searched and know 2007 production it pro ally won't.

Just installed DPs and got a couple of half engine lights within the first 50 miles and then the full engine light has come on. Have can clear on (default)

Did you install the rear o2 sensors? The proceed only clears the cat inefficiency code, not the heater circuit codes.

jdbretz · 06-02-2011, 12:29 PM

What codes are stored?

Noelpolar · 06-03-2011, 04:10 AM

Yes I did install the rear sensors........ Will check what the codes are tomorrow.......

**335i** · 06-03-2011, 03:46 PM

did u solved this?

Noelpolar · 06-03-2011, 08:57 PM

The was only one code a 2C3D 11325 (Lambda probe in front of catalytic converter, control failure) ??????

This code followed a couple of 1/2 engine lights that seemed to clear themselves.

Noelpolar · 06-03-2011, 10:17 PM

Bump

jdbretz · 06-03-2011, 10:18 PM

Quote:

Originally Posted by Noelpolar

The was only one code a 2C3D 11325 (Lambda probe in front of catalytic converter, control failure) ??????

Maybe one of your O2 sensors was damaged during the install of your downpipes. The only other thing I would think is maybe if the O2 sensors were accidentally switched during the re-install. Those are my best guesses. Hope you get it all sorted out.

EDIT: After searching a bit, I think your O2 sensor is damaged or not working. You may need to order a new one if you clear the code and it comes back.

Noelpolar · 06-04-2011, 03:39 AM

I've just done the mode 3 procede resets and will take it on a drive tomorrow to see what happens ........ I was very careful with the o2 sensors when doing the DPs.

The reset of the throttle adaption seemed to work for someone on this thread: http://www.e90post.com/forums/showth...ighlight=11325

Noelpolar · 06-06-2011, 04:05 AM

The reset seemed to cure the 11325 code problem. Still get half engine light every 20 minutes or so that goes after a minute. Raised separate post on this.

turbo2nr · 06-06-2011, 10:24 AM

i have the same problem with codes,

just installed plm downpipes, and the car is running like crap miss firing alot, it will run good for a little and then mis fire and throw check engine light.

i think its because i have a exhaust leak on my downpipe ( i hear it) imma try tight them up and clear codes and hopefully it will be fixed..

06-02-2011, 08:24 AM	#1
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	Procede canclear question Will the can clear functionality on the Procede (v5) clear the codes thrown up by catless DPs on a Jan 2008 production e92 on original dme software? I've searched and know 2007 production it pro ally won't. Just installed DPs and got a couple of half engine lights within the first 50 miles and then the full engine light has come on. Have can clear on (default)
	Appreciate 0 Tweet Quote

06-02-2011, 12:29 PM	#3
jdbretz Captain 56 Rep 923 Posts Drives: '18 X5d, '12 M3 ZCP, '12 F30 Join Date: Dec 2010 Location: FL Panhandle iTrader: (10)	What codes are stored?
	Appreciate 0 Quote

06-03-2011, 04:10 AM	#4
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	Yes I did install the rear sensors........ Will check what the codes are tomorrow.......
	Appreciate 0 Quote

06-03-2011, 03:46 PM	#5
335i Colonel 191 Rep 2,320 Posts Drives: TOYOTA & 2008 E92 335i 6MT Join Date: Jul 2007 Location: Swiss iTrader: (4) Garage List 2008 335i [9.00]	did u solved this? __________________ E92 335i Black Saphire 6MT PROcede V5, BMS DCI, Big Tom IC, AR CL-DP's 3", AR Design OC, Forge DV's, OEM M3 side skirts, BMW Performance Wheels 19 inch 269 Black Gloss+Continental ContiSportContact 5P (400hp and 550nm) https://www.youtube.com/user/aistis7..._as=subscriber
	Appreciate 0 Quote

06-03-2011, 08:57 PM	#6
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	The was only one code a 2C3D 11325 (Lambda probe in front of catalytic converter, control failure) ?????? This code followed a couple of 1/2 engine lights that seemed to clear themselves. Last edited by Noelpolar; 06-03-2011 at 10:16 PM..
	Appreciate 0 Quote

06-03-2011, 10:17 PM	#7
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	Bump
	Appreciate 0 Quote

06-04-2011, 03:39 AM	#9
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	I've just done the mode 3 procede resets and will take it on a drive tomorrow to see what happens ........ I was very careful with the o2 sensors when doing the DPs. The reset of the throttle adaption seemed to work for someone on this thread: http://www.e90post.com/forums/showth...ighlight=11325
	Appreciate 0 Quote

06-06-2011, 04:05 AM	#10
Noelpolar Private First Class 7 Rep 133 Posts Drives: E92 335i Auto Join Date: May 2008 Location: Australia iTrader: (0)	The reset seemed to cure the 11325 code problem. Still get half engine light every 20 minutes or so that goes after a minute. Raised separate post on this.
	Appreciate 0 Quote

06-06-2011, 10:24 AM	#11
turbo2nr 25to4 20 Rep 224 Posts Drives: e90 335i Join Date: Dec 2010 Location: Nyc iTrader: (0)	i have the same problem with codes, just installed plm downpipes, and the car is running like crap miss firing alot, it will run good for a little and then mis fire and throw check engine light. i think its because i have a exhaust leak on my downpipe ( i hear it) imma try tight them up and clear codes and hopefully it will be fixed.. __________________ 1996 s14 600whp
	Appreciate 0 Quote