Best meth components

jippii ensio · 06-04-2011, 02:06 PM

We are building a FBO with upgraded turbos and are looking for the best meth components to support the octane requirements, cooling and fueling needs. We have a big upgraded intercooler with around 90% efficiency and Mr.5 type of an intake to provide cool air. Due to the FMIC heat sink and intake receiving cool air, there is not much need for meth cooling at low boosts, and we aim at high boost meth spraying only. The idea is to have the meth evaporated fully so that it will travel along the air keeping the AFRs in check.

So we would be looking for the highest pressure and finest mist. The highest possible pressure would be with Snow 220psi pump, Coolingmist CM10 nozzle we believe having the finest spray, planning to use CM solenoid and either one tall tank or dual stage tanks or alternatively the washer tank. The charge pipe would be custom made from FMIC exit to throttle body at the TB diameter slowing the air down a bit due to the increased diameter and giving more time for the evaporation. Nozzle location would be far enough from TB to enable full evaporation. Fail safe should be 100% meth compatible, just in case, such as the Snow unit as an example.

The system could be upgraded in case any better components emerge in the market. E.g. CM12 currently under development will be a possibility later on. Have we missed something? Any comments or further suggestions?

Brey335i · 06-04-2011, 02:39 PM

Snow Failsafe, Devil's Own tank and basic kit. And then just set the pressure switch to whatever you want to start spraying at

wren57 · 06-04-2011, 02:44 PM

You're gonna need lots of sudafed and some beakers. Or take a look into Vishnu's PWM kit.

bleicht · 06-04-2011, 02:45 PM

That AEM Injection Monitor safety device thing looks pretty cool... has anyone tried it?

cn555ic · 06-04-2011, 05:07 PM

A little of Snow, a little of Aquamist, a little of Coolingmist, and a little from Lebonte jumble them up together and you have one awesome mutated meth system

themyst · 06-04-2011, 10:44 PM

Quote:

Originally Posted by Brey335i

Snow Failsafe, Devil's Own tank and basic kit. And then just set the pressure switch to whatever you want to start spraying at

That's what I run, no problems.

06-04-2011, 02:06 PM	#1
jippii ensio Major 72 Rep 1,432 Posts Drives: 335i Join Date: Feb 2009 Location: On the road iTrader: (0)	Best meth components We are building a FBO with upgraded turbos and are looking for the best meth components to support the octane requirements, cooling and fueling needs. We have a big upgraded intercooler with around 90% efficiency and Mr.5 type of an intake to provide cool air. Due to the FMIC heat sink and intake receiving cool air, there is not much need for meth cooling at low boosts, and we aim at high boost meth spraying only. The idea is to have the meth evaporated fully so that it will travel along the air keeping the AFRs in check. So we would be looking for the highest pressure and finest mist. The highest possible pressure would be with Snow 220psi pump, Coolingmist CM10 nozzle we believe having the finest spray, planning to use CM solenoid and either one tall tank or dual stage tanks or alternatively the washer tank. The charge pipe would be custom made from FMIC exit to throttle body at the TB diameter slowing the air down a bit due to the increased diameter and giving more time for the evaporation. Nozzle location would be far enough from TB to enable full evaporation. Fail safe should be 100% meth compatible, just in case, such as the Snow unit as an example. The system could be upgraded in case any better components emerge in the market. E.g. CM12 currently under development will be a possibility later on. Have we missed something? Any comments or further suggestions? Last edited by jippii ensio; 06-04-2011 at 02:25 PM..
	Appreciate 0 Tweet Quote

06-04-2011, 02:39 PM	#2
Brey335i Banned 122 Rep 4,771 Posts Drives: e46 ///M3 Join Date: Oct 2009 Location: Austin, TX iTrader: (11)	Snow Failsafe, Devil's Own tank and basic kit. And then just set the pressure switch to whatever you want to start spraying at
	Appreciate 0 Quote

06-04-2011, 02:44 PM	#3
wren57 Roll Tide 615 Rep 2,366 Posts Drives: 335i Join Date: Jul 2010 Location: St Louis iTrader: (10)	You're gonna need lots of sudafed and some beakers. Or take a look into Vishnu's PWM kit. __________________ Fix your broken/stripped cowl bolts with this elegant brass solution! http://www.e90post.com/forums/showthread.php?p=20230306
	Appreciate 0 Quote

06-04-2011, 02:45 PM	#4
bleicht Private 8 Rep 52 Posts Drives: 08 335i Join Date: May 2011 Location: Socal iTrader: (0)	That AEM Injection Monitor safety device thing looks pretty cool... has anyone tried it?
	Appreciate 0 Quote

06-04-2011, 05:07 PM	#5
cn555ic 485 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	A little of Snow, a little of Aquamist, a little of Coolingmist, and a little from Lebonte jumble them up together and you have one awesome mutated meth system
	Appreciate 0 Quote