[M3to335]

Im going to pick up some 3m tape today to install the Aero lip. Before I do so, is there any specific type which I need to look for? Also, are there specific areas it nees to be stuck?

I just dont feel like driving 62 miles to get the tape kit from the dealer.

[scottp999]

I just bought the brand they had at lowes that was rated for outdoor use. I think it was 1 inch wide. There is main aero lip thread where someone marked with red on a picture where they put the tape. Very little is needed.

[DasBlitz]

has anyone had issues of it flying off or anything. That is my worst fear, of a part flying off due to tape losing its stickyness. Also is it hard to take the tape off since it is suppose to be strong?

[scottp999]

if you heat up the area with a blow dryer for a few minutees you should be able to get it off with some patience. I have 4 strips about 3 inches long each, holding mine on just fine.

[montreal_bimmer]

you will have no problem with the tape....

its made for it.... very strong stuff

im installing my front lip tonight, gonna see how that goes..

[M3to335]

NE one know where that thread is?

Im going RIGHT NOW to pick up the tape and all they have is 0.45" thick. That seems crazy thick to me.

[ifaudi]

This one?

[scottp999]

Originally Posted by M3to335

NE one know where that thread is?

Im going RIGHT NOW to pick up the tape and all they have is 0.45" thick. That seems crazy thick to me.

For the inside parts there is actually a little indentation in the piece that you can put two strips of tape in that are about 3 inches long. Then just put another two strips on the very outside of the piece and you should be fine. I used 4 pieces of tape to do the whole thing. No problems at all @ 500 miles it hasn't moved.

[scottp999]

Originally Posted by ifaudi

This one?

That's it and those marks are perfect for where the tape goes.

[M3to335]

What thickness was it? 0.3" or 0.45" ???

[Fartpimpson]

Check my signature of my mod journal. It shows how to install the aero lip with 3M tape. Also, pay extra attention to the center big "V" gap. It's a aero lip, eventually it will moved out a little bit due to down force.

You can pm me your e-mail so I can send you a zip with a lot other member's aero lip pictures that I collected. To be honest, using adhesive is better and leave very less gap. However, you will not be able to take it out if you want to repaint or sell your front lip in the future.

FYI: ACS vs OEM Aero lip in 2nd picture
http://www.e90post.com/forums/showthread.php?t=61446

[ren]

I'm going to use this when I get my front lip. Walgreens and Target carries it, so I'm sure you can easily find it at other places, too.
3M Scotch Exterior Mounting Tape, 1" x 60". This is what holds my front plate, too.

[Minipuck V 2.0]

Originally Posted by erensf

I'm going to use this when I get my front lip. Walgreens and Target carries it, so I'm sure you can easily find it at other places, too.
3M Scotch Exterior Mounting Tape, 1" x 60". This is what holds my front plate, too.

i actuallyu would go with the one that is for automotive purposes ... u can buy that at pep boys ...

[Fartpimpson]

This is not strong enough. The one my body shop use is way thicker. Remember, its a aero front lip, it's not a roof spoiler or trunk lip. The tape can hold it but eventually it will leave a small gap between the joins.

Originally Posted by erensf

I'm going to use this when I get my front lip. Walgreens and Target carries it, so I'm sure you can easily find it at other places, too.
3M Scotch Exterior Mounting Tape, 1" x 60". This is what holds my front plate, too.

[Minipuck V 2.0]

Originally Posted by ifaudi

This one?

i would actually include the points where it touches your bumper. basically to be safe, i would tape along the top edge of the lip

[Fartpimpson]

Yea agree.
Check the mod journal in my signature. It shows where I put the 3M tape.
Oh also, don't forget to get 2 extra screws from the dealer or pepboy to secure your bumper. There's pre-drilled 2 extra holes there. Most likely you will have to take out 5-6 screws (i forgot) from the bottom of your current bumper then put on your lip with 2 extra screws.

Originally Posted by Minipuck V 2.0

i would actually include the points where it touches your bumper. basically to be safe, i would tape along the top edge of the lip

[M3to335]

Ok, still confused by these responses. I just want to know what thickness tape to get

That red roll was only 1.5mm....thats REALLY thin. If i need thin tape, let me know. The roll I am about to go buy is from a paint shop and is 0.3" thick (7.6mm). Is this going to make the lip not sit flush with the bumper?

[Fartpimpson]

7.6MM sounds like the type I used. Go for it.

p.s. is it come like a big roll in the size of a pizza?

Originally Posted by M3to335

Ok, still confused by these responses. I just want to know what thickness tape to get

That red roll was only 1.5mm....thats REALLY thin. If i need thin tape, let me know. The roll I am about to go buy is from a paint shop and is 0.3" thick (7.6mm). Is this going to make the lip not sit flush with the bumper?

[M3to335]

I have no idea.... Ive never even seen it before. I just called Advance Auto and they cary 3m double sided tape also. Thiers is only 1/6" thick and is used for body molding specifically. Crap, Im confused.

[Fartpimpson]

You can never go wrong with a body shop. If they use that 3M, it should be fine.

Originally Posted by M3to335

I have no idea.... Ive never even seen it before. I just called Advance Auto and they cary 3m double sided tape also. Thiers is only 1/6" thick and is used for body molding specifically. Crap, Im confused.

[Minipuck V 2.0]

Originally Posted by M3to335

I have no idea.... Ive never even seen it before. I just called Advance Auto and they cary 3m double sided tape also. Thiers is only 1/6" thick and is used for body molding specifically. Crap, Im confused.

actually thickness doesn't matter too much just cause i bought the really thin one i forget the size one time and it didn't stick too well. as long as the thickness is under a quarter of a inch?

[Fartpimpson]

Ok here are some pictures for the gap you will possibly get.