[fl335i]

Has anyone else been able to connect to their procede with windows 7? I spent about 1hr figuring out what was going on and realized I needed to download some driver, then found it was connected to COM3. But even after all that the thing won't connect. I changed my power settings to disable the USB gimic per another thread on here refrenced by Vishnu's directions. I need some help here guys.

[fl335i]

Downloaded the driver and the read me first directions. Will try it again tomorrow morning. Hopefully this fixes it. B/c windows updated it.... so I'm assuming I have the newer version that does not work.

[a75787695]

I try the windows7 and not work too. and i use windows xp is working good...

[messi]

What cable are you using. I had a similar problem. Also which rev are you using 2.5 or 3? I have the 2.5 and Vishnu recommends a specific serial to USB cable. Utek from amazon. That still didn't work for me so I a, just gonna get an old lap top and run windows xp on it.

[MR. BONEZ]

Here instead of getting a different computer and so on just download windows xp virtual you can run it on windows 7 will make your life a lot easier here is the link http://www.microsoft.com/windows/vir.../download.aspx

[R1000K3]

No problems here with Win 7, 64 Bit.

[GeorgiaTech335coupe]

I have rev3 and my computer is Win7 64 bit Professional. They don't get along. I had to download Windows XP Virtual Machine (free for Win7 64bit Pro). This works fine. The problem I was having was that Win7 didn't like the driver for the cable.

[FirstBMWLA]

No problems here with rev 2.5 and windows 7 64bit

[qdtjant]

No problems here either. Windows 7 64 bit.

[cn555ic]

I had to download many drivers before I finally found one that didn't drop connection.

[fl335i]

Got it working today pretty fast. I downloaded the driver from Vishnu's site. Followed the read me first and boom, up and running. I enabled my No lift shift Bumped the boost to 20psi on MAP 2. Map 1 & 2 were both 18psi and everything looked identical... thought 2 was supposed to be more aggressive.

[messi]

Isn't map two when you make changes?

[fl335i]

Not sure man^. I think it's just the ability to have two different maps. I'm going to call Vishnu today and run this by them.

[GeorgiaTech335coupe]

Originally Posted by fl335i

Not sure man^. I think it's just the ability to have two different maps. I'm going to call Vishnu today and run this by them.

It has 2 purposes. Can be a second map with different/more aggressive settings or it is the second map for people who have meth for the Procede to switch over to during meth flow.

[GeorgiaTech335coupe]

Originally Posted by fl335i

Got it working today pretty fast. I downloaded the driver from Vishnu's site. Followed the read me first and boom, up and running. I enabled my No lift shift Bumped the boost to 20psi on MAP 2. Map 1 & 2 were both 18psi and everything looked identical... thought 2 was supposed to be more aggressive.

Unless you are running race gas and FBO+meth, 20 lbs of boost is going to be too much in the FL heat. I don't run that much and I'm FBO+meth+e85 mix, here in FL.

Also, depending on what map you are running, 100% does not equal 20 lbs. It equals boost setpoints equal to the 100% boost table (which may hit 20 psi in the midrange). The maps that a lot of people are running currently have a 0% boost table and a 100% boost table. The UT value you put in averages the 2 tables by the percent that you enter for your boost table. Not sure what map you are running though.

[hasta la pasta 27]

Im stuck trying to keep my procede rev2.5 from disconnecting from my W7 64bit. tried everything and nothing =( any input?

p.s. i cant run virtual mode because i have windows 7 home

[jdbretz]

Check out this thread and see if it helps you:

http://www.e90post.com/forums/showth...de+disconnects