Failed emissions with JB4 and V3 BMS DP Fix

E92ML · 08-13-2013, 08:38 PM

I installed my new V3 BMS DP fix this morning, set the dial to 5pm (default) and then drove for 70 miles. I took the emissions tests on Map 0 and failed. The results/specifics are below. Can anyone help me out here? Do I need to clear codes with the JB4 right before testing? Or do I need to adjust the dial up/down?

Thanks for the help.

///M3NACE · 08-13-2013, 08:39 PM

There is no data your showing but get a scan tool! It will tell you if the monitors are ready or not. You can have up to 1 not ready

E92ML · 08-13-2013, 08:42 PM

Quote:

Originally Posted by ihsanshaik

There is no data your showing but get a scan tool! It will tell you if the monitors are ready or not. You can have up to 1 not ready

Sorry, just posted the picture below. I'd like to avoid spending more money as I already bought the V3 DP fix but I'll buy the scan tool if I need to.

roadkillrob · 08-13-2013, 08:55 PM

Readiness is not set and it says failed due to codes, so looks like you need to clear codes and then drive some more to set readiness. Readiness is a cycle, just driving 70 miles will not necessarily set.

clear the codes with the jb4, buy a $15 obdII scan tool that will read readiness, and then do the drive cycle.

Scan tool amazon this one works I have it

http://www.amazon.com/Autel-MaxiScan...=Acutely+ms300

Follow drive cycle, then confirm readiness with tool.

http://www.m5board.com/vbulletin/att...-procedure.pdf

In my case I cleared codes, got readiness, got it tested and a week later codes came back and had to adjust from 5 to 6 o'clock.

Good luck!

buster84 · 08-13-2013, 08:58 PM

Quote:

Originally Posted by E92ML

I installed my new V3 BMS DP fix this morning, set the dial to 5pm (default) and then drove for 70 miles. I took the emissions tests on Map 0 and failed. The results/specifics are below. Can anyone help me out here? Do I need to clear codes with the JB4 right before testing? Or do I need to adjust the dial up/down?

Thanks for the help.

Maybe you didnt drive enough before your smog... You need to make sure you car is fully warm and for all the sensors to function correctly. If you have a sniffer test you need your cats warm which means 30mins of driving first. Its also possible that the smog guy accidentally hit your cruise control or touched it on purpose (because he didnt know what it was??) If that was to happen it would reset everything and your forced to drive another 70+ miles.

This probably didn't happen and there is a real small chance it could, but you never know. People do like to press buttons in cars they dont normally see lol. If you dont want to remove it you can also disable the steering wheel controls from what i've heard.

zeel · 08-13-2013, 09:07 PM

Clear the codes. Then turn off autoclear. Then drive cycle for readiness.

guwakjai010 · 08-13-2013, 10:59 PM

i dunno about washington but i'm an inspector in PA... In PA your only allowed one thing to be not ready and cannot have any check engine light codes... but since my car has downpipes and jb4, i kept my autoclear on and when u have your autoclear on, everything that says ready or not ready becomes unsupported which means it doesn't exist... and obviously no codes so thats how i passed emissions in PA.... also we do not do the tailpipe test for obd2 cars.

Tiago@VRSF · 08-13-2013, 11:21 PM

Sounds like you have canclear/autoclear on. Disable that and let the simulator work its magic.

E92ML · 08-13-2013, 11:44 PM

Quote:

Originally Posted by roadkillrob

Readiness is not set and it says failed due to codes, so looks like you need to clear codes and then drive some more to set readiness. Readiness is a cycle, just driving 70 miles will not necessarily set.

clear the codes with the jb4, buy a $15 obdII scan tool that will read readiness, and then do the drive cycle.

Scan tool amazon this one works I have it

http://www.amazon.com/Autel-MaxiScan...=Acutely+ms300

Follow drive cycle, then confirm readiness with tool.

http://www.m5board.com/vbulletin/att...-procedure.pdf

In my case I cleared codes, got readiness, got it tested and a week later codes came back and had to adjust from 5 to 6 o'clock.

Good luck!

Quote:

Originally Posted by zeel

Clear the codes. Then turn off autoclear. Then drive cycle for readiness.

Quote:

Originally Posted by Tiago@VRSF

Sounds like you have canclear/autoclear on. Disable that and let the simulator work its magic.

Perfect thanks for all the help! So I need to turn off auto clear, clear the codes and then do a drive cycle for readiness. Can I do the drive cycle and then clear the codes? Or does the drive cycle need to be done last

pinky_and_me · 08-14-2013, 04:49 AM

Every time you clear codes readiness is reset so no.

pits200 · 08-14-2013, 07:28 AM

Setting readiness is no fun if you don't live in an open area where you can drive properly to reset all items. You don't have to follow it to a t but it has to be very close.

pwilde · 08-14-2013, 09:10 AM

get a cobb or procede...

Mike@N54Tuning.com · 08-14-2013, 09:46 AM

Quote:

Originally Posted by pwilde

get a cobb or procede...

How will that help?

Mike

WLF · 08-14-2013, 09:53 AM

Quote:

Originally Posted by pwilde

get a cobb or procede...

Quote:

Originally Posted by Mike@N54Tuning.com

How will that help?

Mike

08-13-2013, 08:38 PM	#1
E92ML Captain 37 Rep 886 Posts Drives: E92 2008 335xi Coupe Join Date: May 2011 Location: Bellevue, WA iTrader: (0)	Failed emissions with JB4 and V3 BMS DP Fix I installed my new V3 BMS DP fix this morning, set the dial to 5pm (default) and then drove for 70 miles. I took the emissions tests on Map 0 and failed. The results/specifics are below. Can anyone help me out here? Do I need to clear codes with the JB4 right before testing? Or do I need to adjust the dial up/down? Thanks for the help. Attached Images __________________ Performance: JB4 ECU, CP-E DP's, WW BMS Meth Kit, AR meth elbow, BMS DCI, AFE Intake Scoops, Exterior: Enkruez 19" H8R, H&R Spacers, Aero Lip, Tint, ACS Roof Spoiler, HID AE's, HID Fogs, Black Grills, Sport Pedals
	Appreciate 0 Tweet Quote

08-13-2013, 08:39 PM	#2
///M3NACE Banned 184 Rep 3,900 Posts Drives: E36 M3, E36 Vert , E90 N52 Join Date: Oct 2006 Location: Downers Grove, IL iTrader: (5)	There is no data your showing but get a scan tool! It will tell you if the monitors are ready or not. You can have up to 1 not ready
	Appreciate 0 Quote

08-13-2013, 08:55 PM	#4
roadkillrob Major General 897 Rep 5,476 Posts Drives: 08 335i,22 X3M, 2012 C63 Black Join Date: Jul 2007 Location: NH iTrader: (15)	Readiness is not set and it says failed due to codes, so looks like you need to clear codes and then drive some more to set readiness. Readiness is a cycle, just driving 70 miles will not necessarily set. clear the codes with the jb4, buy a $15 obdII scan tool that will read readiness, and then do the drive cycle. Scan tool amazon this one works I have it http://www.amazon.com/Autel-MaxiScan...=Acutely+ms300 Follow drive cycle, then confirm readiness with tool. http://www.m5board.com/vbulletin/att...-procedure.pdf In my case I cleared codes, got readiness, got it tested and a week later codes came back and had to adjust from 5 to 6 o'clock. Good luck! __________________ 2025 X5 Msport 2008 E93 335i FBO 2012 Mercedes C63 Black Series Alanite Grey
	Appreciate 0 Quote

08-13-2013, 09:07 PM	#6
zeel Lieutenant 14 Rep 579 Posts Drives: 08 AW e92 335i Join Date: Nov 2010 Location: MD/NOVA/DC iTrader: (2) Garage List 2008 bmw e92 335i [7.34]	Clear the codes. Then turn off autoclear. Then drive cycle for readiness. __________________ 11.76 @ 124mph (123.9) full weight/street tires/no meth.
	Appreciate 0 Quote

08-13-2013, 10:59 PM	#7
guwakjai010 Enlisted Member 14 Rep 42 Posts Drives: E92 335i Join Date: Jun 2011 Location: PA iTrader: (0)	i dunno about washington but i'm an inspector in PA... In PA your only allowed one thing to be not ready and cannot have any check engine light codes... but since my car has downpipes and jb4, i kept my autoclear on and when u have your autoclear on, everything that says ready or not ready becomes unsupported which means it doesn't exist... and obviously no codes so thats how i passed emissions in PA.... also we do not do the tailpipe test for obd2 cars.
	Appreciate 0 Quote

08-13-2013, 11:21 PM	#8
Tiago@VRSF 2126 Rep 43,349 Posts Drives: F90 M5 Join Date: Dec 2007 Location: Doral, FL iTrader: (99) Garage List 2014 F30 328xi [0.00] 2015 F82 BMW M4 [0.00] 2013 Ducati 1199 Pa ... [0.00] 2008 BMW 335i [0.00]	Sounds like you have canclear/autoclear on. Disable that and let the simulator work its magic.
	Appreciate 0 Quote

08-14-2013, 04:49 AM	#10
pinky_and_me Second Lieutenant 13 Rep 294 Posts Drives: N54 335xi Join Date: Feb 2011 Location: Cleveland, OH iTrader: (0)	Every time you clear codes readiness is reset so no.
	Appreciate 0 Quote

08-14-2013, 07:28 AM	#11
pits200 Colonel 556 Rep 2,598 Posts Drives: 09 335i X-Drive Black Sapphire Join Date: Mar 2010 Location: Pittsburgh iTrader: (1)	Setting readiness is no fun if you don't live in an open area where you can drive properly to reset all items. You don't have to follow it to a t but it has to be very close.
	Appreciate 0 Quote

08-14-2013, 09:10 AM	#12
pwilde Private First Class 21 Rep 147 Posts Drives: 2008 335i 6spd Join Date: Jan 2012 Location: Madison, WI iTrader: (0) Garage List 2008 BMW [0.00]	get a cobb or procede...
	Appreciate 0 Quote