V2 Re-install

e92law · 11-08-2007, 12:50 PM

V2 Re-install

I completely removed my V2 Procede prior to service and now need to get it back in there ASAP. Killing me knowing how much power I am leaving on my desk at home. Anyways, are there instructions for a “fresh” install? I would rather not go through the process of using the V1 instructions and then using the V2 instructions.

Also, at the same time, I figure that I might as well install the speed sensor wire to the Procede (white/green wire of pin #17 of the grey sub-connector of the smaller ECU harness to digital input #4 of the black Procede connector) Does this sound correct? Even so, I would really like some instructions with pictures. Any ideas? Help!

O-cha · 11-08-2007, 12:51 PM

You're going to have to do both either way. The only connector that the two installs shared is replacement of the green wire. So basically if you follow v1 install then v2, you wont do the same thing twice at all.

Kbueno · 11-08-2007, 12:54 PM

Quote:

Originally Posted by e92law

V2 Re-install

I completely removed my V2 Procede prior to service and now need to get it back in there ASAP. Killing me knowing how much power I am leaving on my desk at home. Anyways, are there instructions for a “fresh” install? I would rather not go through the process of using the V1 instructions and then using the V2 instructions.

Also, at the same time, I figure that I might as well install the speed sensor wire to the Procede (white/green wire of pin #17 of the grey sub-connector of the smaller ECU harness to digital input #4 of the black Procede connector) Does this sound correct? Even so, I would really like some instructions with pictures. Any ideas? Help!

FYI: Until v2.02 is released, intercepting the speed sensor wire will throw a code.

munters · 11-08-2007, 01:13 PM

I did it and there is no code. Maybe if you not change the map..

e92law · 11-08-2007, 01:27 PM

Quote:

Originally Posted by 335lvr

FYI: Until v2.02 is released, intercepting the speed sensor wire will throw a code.

Anyone have more information on this? Also, since v.2.02 is out this week, maybe Vishnu will have updated instructions also?

anonemouse · 11-08-2007, 02:00 PM

I also had to remove and reinstall V2 last week. To make things easy to reinstall when I removed proceed I labeled the wires with light color insullating tape, and wrote on it information such as "SB6" - meaning Small ECU connector, black subconnector wire 6, "LW7" - Large ECU connector, white subconnector wire 7. There are 6 wires that need labelled.

I labeled the wires connected to the proceed V1/V2 looms that are being removed, obviously not labelling any of the original ECU wires!

When I did the restore just to make sure I didn't screw up I put togther this cheat sheet from V1/V2 information, if you have done an install yourself this information should make sense:

Ground to to 10mm nut

Power to switched power source

Small ECU connector
- Black subconnector
- Wire 6 - Yellow with white stripe (#525)
intercept with female wire from yellow loom

- Wire 7 - Yellow with white stripe (no number)
intercept with other female wire from yellow loom

Large ECU connector
- Black subconnector
- Wire 29 - solid yellow (#494)
intercept with female wire from white loom

- Wire 10 - Solid yellow (#1324)
intercept with female wire from green loom

- White subconnector
- Wire 7 - White with grey strip
intercept with one of longer wires in V2 loom

- Wire 14 - solid white (#837)
intercept with other longer wire in V2 loom

Hope this is useful.

A.

e92law · 11-08-2007, 02:15 PM

That is perfect. Thank you very much. All you need in a few lines. Now we just need this for the speed wire also.

Kbueno · 11-08-2007, 03:55 PM

Quote:

Originally Posted by e92law

Anyone have more information on this? Also, since v.2.02 is out this week, maybe Vishnu will have updated instructions also?

He won't have instructions, but someone will..Eugen?

e.n335 · 11-08-2007, 04:40 PM

Quote:

Originally Posted by 335lvr

He won't have instructions, but someone will..Eugen?

http://www.e90post.com/forums/showthread.php?t=89326

Posting #7

- Eugen

roller84 · 11-08-2007, 07:28 PM

Quote:

Originally Posted by e.n335

http://www.e90post.com/forums/showthread.php?t=89326

Posting #7

- Eugen

Have you been able to test it out yet?

e92law · 11-09-2007, 02:14 PM

What if i intercept the speed wire and just wait for version 2.02? kaboom?

e.n335 · 11-09-2007, 02:42 PM

Quote:

Originally Posted by e92law

What if i intercept the speed wire and just wait for version 2.02? kaboom?

Probably you will get an error code. Why would you like to do this ?

e92law · 11-09-2007, 03:57 PM

Because I am not computer savy enough to fix the code for 2.01. Also, I would rather just upload a new map when 2.02 comes out rather than open everything up for just one wire.

e92law · 11-09-2007, 05:54 PM

Just finished the re-install. Went fine except for one thing…threw out my back. F---- I am only 28, where do I go from here?

Hahaha I was literally laying on the ground hardly able to breath it hurt so bad, engine cover open and pieces all over the place, and people walking by. It must have looked like my car tried to eat me.

Ruff Rider · 11-09-2007, 06:02 PM

Quote:

Originally Posted by e92law

It must have looked like my car tried to eat me.

Now that's some funny shit

(sorry for your back problem)

11-08-2007, 12:50 PM	#1
e92law First Lieutenant 24 Rep 340 Posts Drives: e70 Join Date: Sep 2006 Location: AZ iTrader: (0)	V2 Re-install V2 Re-install I completely removed my V2 Procede prior to service and now need to get it back in there ASAP. Killing me knowing how much power I am leaving on my desk at home. Anyways, are there instructions for a “fresh” install? I would rather not go through the process of using the V1 instructions and then using the V2 instructions. Also, at the same time, I figure that I might as well install the speed sensor wire to the Procede (white/green wire of pin #17 of the grey sub-connector of the smaller ECU harness to digital input #4 of the black Procede connector) Does this sound correct? Even so, I would really like some instructions with pictures. Any ideas? Help!
	Appreciate 0 Tweet Quote

11-08-2007, 12:51 PM	#2
O-cha Brigadier General 244 Rep 4,726 Posts Drives: Mcoupe Join Date: Oct 2007 Location: In front of you iTrader: (2)	You're going to have to do both either way. The only connector that the two installs shared is replacement of the green wire. So basically if you follow v1 install then v2, you wont do the same thing twice at all. __________________
	Appreciate 0 Quote

11-08-2007, 02:00 PM	#6
anonemouse Private First Class 16 Rep 159 Posts Drives: Santorini Blue F80 M3 Join Date: Mar 2007 Location: NorCal iTrader: (0)	I also had to remove and reinstall V2 last week. To make things easy to reinstall when I removed proceed I labeled the wires with light color insullating tape, and wrote on it information such as "SB6" - meaning Small ECU connector, black subconnector wire 6, "LW7" - Large ECU connector, white subconnector wire 7. There are 6 wires that need labelled. I labeled the wires connected to the proceed V1/V2 looms that are being removed, obviously not labelling any of the original ECU wires! When I did the restore just to make sure I didn't screw up I put togther this cheat sheet from V1/V2 information, if you have done an install yourself this information should make sense: Ground to to 10mm nut Power to switched power source Small ECU connector - Black subconnector - Wire 6 - Yellow with white stripe (#525) intercept with female wire from yellow loom - Wire 7 - Yellow with white stripe (no number) intercept with other female wire from yellow loom Large ECU connector - Black subconnector - Wire 29 - solid yellow (#494) intercept with female wire from white loom - Wire 10 - Solid yellow (#1324) intercept with female wire from green loom - White subconnector - Wire 7 - White with grey strip intercept with one of longer wires in V2 loom - Wire 14 - solid white (#837) intercept with other longer wire in V2 loom Hope this is useful. A.
	Appreciate 0 Quote

11-09-2007, 02:14 PM	#11
e92law First Lieutenant 24 Rep 340 Posts Drives: e70 Join Date: Sep 2006 Location: AZ iTrader: (0)	What if i intercept the speed wire and just wait for version 2.02? kaboom?
	Appreciate 0 Quote

11-09-2007, 05:54 PM	#14
e92law First Lieutenant 24 Rep 340 Posts Drives: e70 Join Date: Sep 2006 Location: AZ iTrader: (0)	Just finished the re-install. Went fine except for one thing…threw out my back. F---- I am only 28, where do I go from here? Hahaha I was literally laying on the ground hardly able to breath it hurt so bad, engine cover open and pieces all over the place, and people walking by. It must have looked like my car tried to eat me.
	Appreciate 0 Quote

11-08-2007, 01:13 PM	#4
munters Captain 11 Rep 677 Posts Drives: E91 335XI AT Dakota Black M Join Date: Jun 2007 Location: Switzerland iTrader: (0)	I did it and there is no code. Maybe if you not change the map..
	Appreciate 0 Quote

11-08-2007, 02:15 PM	#7
e92law First Lieutenant 24 Rep 340 Posts Drives: e70 Join Date: Sep 2006 Location: AZ iTrader: (0)	That is perfect. Thank you very much. All you need in a few lines. Now we just need this for the speed wire also.
	Appreciate 0 Quote

11-09-2007, 03:57 PM	#13
e92law First Lieutenant 24 Rep 340 Posts Drives: e70 Join Date: Sep 2006 Location: AZ iTrader: (0)	Because I am not computer savy enough to fix the code for 2.01. Also, I would rather just upload a new map when 2.02 comes out rather than open everything up for just one wire.
	Appreciate 0 Quote